background image

b) If error conditions appear, reinstall FlexRIO Support and the PXIe-5763.

What Should I Do if the PXIe-5763 Fails the Self-Test?

1. Restart the system.
2. Launch MAX, and perform the self-test again.
3. Power off the chassis.
4. Reinstall the failed module in a different slot.
5. Power on the chassis.
6. Perform the self-test again.

Where to Go Next

Refer to the following figure for information about other product tasks and associated

resources for those tasks.

custom applications within

an application programming 

interface (API).

about hardware features

or review device specifications.

more about your products through 

ni.com.

the application development

environment (ADE)

for your application.

*This item is also installed with the driver software.

Support

ni.com/support

Located at 

ni.com/manuals

FlexRIO

ni.com/flexrio

Services

ni.com/services

Located in LabVIEW Example Finder

PXIe-5763
Specifications, 

FlexRIO Help* 

Getting Started
with LabVIEW

LabVIEW FPGA
Module Help

FlexRIO Module
Examples* 

NI PXIe-7911

Worldwide Support and Services

The NI website is your complete resource for technical support. At 

ni.com/support

, you have

access to everything from troubleshooting and application development self-help resources to

email and phone assistance from NI Application Engineers.

PXIe-5763 Getting Started Guide

  | 

© National Instruments

  | 

13

Summary of Contents for PXIe-5763
















Reviews: