background image

6

|

ni.com

|

PXIe-4310 and TB-4310 (10V)/TB-4310 (600V) 

8.

Secure the module to the chassis using the front-panel captive screws, shown in Figure 2. 
Tighten the screws to 0.31 N · m (2.7 lb · in.).

9.

Install a filler panel in any empty slots.

Figure 2.  

Installing PXIe-4310

 

Modules

Connect the Signals

Caution

To ensure the specified EMC performance, operate this product only with 

shielded cables and shielded accessories. Use only twisted, shielded pair cables for 
channel connections. Refer to the 

PXIe-4310 User Manual

 for specific guidance on 

terminating cable shields.

Caution

Do not supply hazardous voltages (>30 V

rms

/42.4 V

pk

/60 VDC) to the 

terminal block without the terminal block being connected to the PXIe-4310.

A terminal block is required to make connections to the module. To connect signals to the 
TB-4310 (10V)/TB-4310 (600V) refer to Figures 3 and 4 while completing the following steps:

Note

You can find the pinout names and locations in Measurement & Automation 

Explorer (MAX) at any time by right-clicking the device name under 

Devices and 

Interfaces

 and selecting 

Device Pinouts

.

1.

Loosen the captive top cover screws and remove the top cover.

2.

Loosen the strain-relief screws and remove the strain-relief bar.

3.

Prepare the shielded signal wire by stripping the insulation no more than 8 mm (0.24 in.).

4.

Run the shielded signal wires through the strain-relief opening.

1

Captive  Screws

NI

 PX

Ie-1062Q

CO

OLING

 CL

EAR

ANCE

 AND 

FAN 

FILT

ER 

MA

INT

ENA

NCE

 RE

QUI

RE

D. 

S

EE MA

NU

AL.

1

 NAT

ION

AL 

INSTR

UM

ENTS

Summary of Contents for PXIe-4310

























Reviews: