National Instruments NI PXIe-8105 User Manual Download

Page: 67 / 76

Glossary

National Instruments Corporation

G-3

NI PXIe-8105 User Manual

EPP

Enhanced Parallel Port.

expansion ROM

An onboard EEPROM that may contain device-specific initialization and
system boot functionality.

FCC

Federal Communications Commission.

1. Grams.
2. A measure of acceleration equal to 9.8 m/s

GPIB

General Purpose Interface Bus (IEEE 488).

rms

A measure of random vibration—The root mean square of acceleration
levels in a random vibration test profile.

Hertz—Cycles per second.

I/O

Input/output—The techniques, media, and devices used to achieve
communication between machines and users.

IDE

Integrated Drive Electronics—Hard disk and built-in controller.

IEEE

Institute of Electrical and Electronics Engineers.

in.

Inches.

instrument driver

A set of routines designed to control a specific instrument or family of
instruments, and any necessary related files for LabWindows/CVI or
LabVIEW.

interrupt

A means for a device to request service from another device.

interrupt level

The relative priority at which a device can interrupt.

Summary of Contents for NI PXIe-8105













































































Search results

Summary of Contents for NI PXIe-8105

Reviews:

Related manuals for NI PXIe-8105

Brands by name

Popular brands

National Instruments NI PXIe-8105, User Manual

Search results

Summary of Contents for NI PXIe-8105

Reviews:

Related manuals for NI PXIe-8105

Brands by name

Popular brands