National Instruments NI PXIe-8105 User Manual Download

Page: 62 / 76

Appendix A

Specifications

National Instruments Corporation

A-5

NI PXIe-8105 User Manual

CE Compliance

This product meets the essential requirements of applicable European
Directives, as amended for CE marking, as follows:

•

73/23/EEC; Low-Voltage Directive (safety)

•

89/336/EEC; Electromagnetic Compatibility Directive (EMC)

Note

Refer to the Declaration of Conformity (DoC) for this product for any additional

regulatory compliance information. To obtain the DoC for this product, visit

ni.com/certification

, search by model number or product line, and click the

appropriate link in the Certification column.

Waste Electrical and Electronic Equipment (WEEE)

EU Customers

At the end of their life cycle, all products

must

be sent to a WEEE recycling

center. For more information about WEEE recycling centers and National Instruments
WEEE initiatives, visit

ni.com/environment/weee.htm

Summary of Contents for NI PXIe-8105













































































Search results

Summary of Contents for NI PXIe-8105

Reviews:

Related manuals for NI PXIe-8105

Brands by name

Popular brands

National Instruments NI PXIe-8105, User Manual

Search results

Summary of Contents for NI PXIe-8105

Reviews:

Related manuals for NI PXIe-8105

Brands by name

Popular brands