National Instruments NI PXIe-8105 User Manual Download | Manualshive

Page: 31 / 76

background image

Chapter 2

Installation and Configuration

©

National Instruments Corporation

2-17

NI PXIe-8105 User Manual

If you need to recover your factory-installed operating system from a CD,
you can use the included OS re-installation CD with an external USB
CD/DVD-ROM drive such as a USB CD/DVD-ROM drive. Boot the
PXI Express controller using the OS re-installation CD to recover the OS.
You also may need to reinstall other software after using the CD to recover
the OS.

Note

Recovering the OS erases the contents of your hard disk. Back up any files you want

to keep.

Installing an OS

NI PXIe-8105 controllers include a preinstalled OS. In some cases, you
may want to install a different OS. When doing so, consider the following
guidelines.

Installing from a USB CD/DVD-ROM

The NI PXIe-8105 supports the installation of Windows XP from a USB
CD/DVD-ROM. However, many other operating systems do not support
installation from a USB CD/DVD-ROM. For example, Windows 2000
aborts during the install process because it does not have drivers for the
USB CD/DVD-ROM device.

As an alternative to a USB CD/DVD-ROM drive, you can use an external
SCSI CD-ROM with a PXI-SCSI adapter.

Note

For additional assistance with installing or changing an operating system, refer to

KnowledgeBase 2ZKC02OK at

ni.com/support

.

«
...
29
30
31
32
33
...
»

Summary of Contents for NI PXIe-8105













































































Reviews:

No comments

Related manuals for NI PXIe-8105

Univerge SV9300

Brand: NEC Pages: 26

Brand: NEC Pages: 20

DS2000 IntraMail

Brand: NEC Pages: 2

Brand: Palo Alto Network Pages: 56

Brand: 3Com Pages: 18

Brand: Supermicro Pages: 24

Brand: Genie Pages: 15

Brand: ZALMAN Pages: 4

HIRESCHMANN IT MAMMUTHUS MTM8003-FAN

Brand: Belden Pages: 84

Mercury FireWire 400

Brand: OWC Pages: 2

Brand: Z-Com Pages: 18

crown PIP Series

Brand: Harman Pages: 16

Brand: Alcatel-Lucent Pages: 12

netHOST NHST-T100

Brand: hilscher Pages: 75

Brand: Baikal Miner Pages: 14

Brand: uneron Pages: 13

Brand: Cypress Semiconductor Pages: 26

Brand: Corsair Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands