National Instruments NI PXIe-8105 User Manual Download | Manualshive

Page: 23 / 76

background image

Chapter 2

Installation and Configuration

©

National Instruments Corporation

2-9

NI PXIe-8105 User Manual

only for modern operating systems such as Windows XP or 2000. The
default setting is

Enabled

.

Note

Refer to KnowledgeBase 3SIC67D8 at

ni.com/support

for detailed information

about switching between APIC and legacy PIC mode for Windows operating systems.

•

PIRQx Routing

—This setting selects the routing option for

PXI Express/PCI Express devices connected to PIRQx. This setting
affects OSes that do not use APIC routing. The default setting for all
PIRQx options is

IRQ10

.

•

PCI Option ROM Error Reporting

—When set to

Enabled

this

setting allows the BIOS to display error messages when trying to load
PCI Option ROMs. The BIOS may pause the boot process and wait for
user input. When set to

Disabled

all Option ROM errors at boot time

are ignored.

Security Menu

Use this menu to enable BIOS security options.

•

Set User Password

—This setting allows you to specify a password

that must be entered to boot the system. To activate this feature, you
must first specify a Supervisor password and enable the

Password on

boot

feature. By default, no password is specified.

•

Set Supervisor Password

—This setting allows you to specify a

password that must be entered to access the BIOS setup options. By
default, no password is specified.

•

Password on Boot

—This setting controls whether or not a password

is required to boot the system. If enabled, the user must enter the User
Password to boot the system. The default setting is

Disabled

.

•

Write Protect Boot Sector

—When set to

Yes

, this setting prevents

modification of a hard disk boot sector via INT 13h services, which
may help prevent certain computer viruses from infecting the
controller. This setting does not prevent boot sector modification by
32-bit operating system drivers that access the hard disk directly. The
default is

No

.

«
...
21
22
23
24
25
...
»

Summary of Contents for NI PXIe-8105













































































Reviews:

No comments

Related manuals for NI PXIe-8105

Brand: DBM Pages: 50

Brand: FOR-A Pages: 39

Brand: Supermicro Pages: 16

Brand: hilscher Pages: 154

TD-3316B4-16P-A1

Brand: TVT Digital Pages: 2

Brand: H3C Pages: 9

Brand: Kramer Pages: 2

Brand: Hauppauge Pages: 62

Brand: Accusys Pages: 34

PXI Terminal Block NI TB-2709

Brand: National Instruments Pages: 12

Brand: Sony Ericsson Pages: 2

Brand: Inspired Energy Pages: 5

Brand: Paradyne Pages: 108

Brand: ICOP Technology Pages: 42

Brand: Netequalizer Pages: 14

Brand: HighPoint Pages: 12

Sporlan Division SCS-PB Series

Brand: Parker Pages: 10

Brand: ZALMAN Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands