National Instruments NI PXIe-8103 User Manual Download Page 14 | Manualshive

Page: 14 / 75

background image

Chapter 1

Introduction

NI PXIe-8103 User Manual

1-4

ni.com

•

The

SMB to PXI

Trigger

provides a routable connection of the

PXI Express triggers to/from the SMB on the front panel.

•

The

Watchdog Timer

block consists of a watchdog timer that can reset

the controller or generate a trigger.

•

The

Chipset ICH6M

connects to the PCI, USB, Serial ATA, and LPC

buses.

•

The

USB Connectors

connect the chipset to the Hi-Speed USB 2.0

interface.

•

The

Serial ATA Hard Disk

is a 40 GB or larger notebook hard disk. The

Serial ATA interface enables transfer rates up to 1.5 Gb/s. The hard
disk also supports Native Command Queuing.

•

The

PXI Express Connector

connects the NI PXIe-8103 to the PXI

Express/CompactPCI Express backplane.

•

The

Super I/O

block represents the other peripherals supplied by the

NI PXIe-8103.

The NI PXIe-8103 has one serial port, and an ECP/EPP

parallel port.

•

The

Gigabit Enet

connects to either 10 Mbit, 100 Mbit, or 1,000 Mbit

Ethernet interfaces.

•

The

GPIB

block contains the GPIB interface.

•

The

ExpressCard/34

slot accommodates an ExpressCard/34 module.

National Instruments Software

National Instruments has developed several software tools you can use with
the NI PXIe-8103.

National Instruments’ hardware and software work together to help you
make the most of your PXI Express system. The LabVIEW, Measurement
Studio, and LabWindows™/CVI™ application development environments
combine with leading hardware drivers such as NI-DAQmx to provide
exceptional control of NI hardware. Instrument drivers are available at

ni.com/idnet

to simplify communication with instruments over a variety

of busses.

LabVIEW is a powerful and easy-to-use graphical programming
environment you can use to acquire data from thousands of different
instruments including USB, IEEE 488.2, VXI, serial, PLCs, and plug-in
boards. LabVIEW helps you convert acquired data into meaningful results
using powerful data analysis routines. Add-on tools provide additional

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
12
13
14
15
16
...
»

Summary of Contents for NI PXIe-8103












































































Reviews:

No comments

Related manuals for NI PXIe-8103

PCMCIA WIRELESS ASAPTER DWL-650

Brand: D-Link Pages: 5

PowerLine DHP-W611AV

Brand: D-Link Pages: 78

xStack Storage DSN-4000 Series

Brand: D-Link Pages: 5

Brand: CAME Pages: 19

Brand: F5 Pages: 2

Brand: F5 Pages: 90

Brand: F5 Pages: 47

DM/IP601-CPCI-100BT

Brand: Dialogic Pages: 2

NVIP- NVRA0104/GO

Brand: Novus Pages: 44

Brand: TANDBERG Pages: 3

Brand: Renesas Pages: 76

Mustang-M2AE-MX1

Brand: IEI Technology Pages: 58

Brand: ADS Technologies Pages: 1

Brand: CSL Pages: 24

Brand: ADTRAN Pages: 136

Brand: Valcom Pages: 3

Brand: ZALMAN Pages: 8

32R1860 - Nortel Layer 2/3 Copper GbE Switch...

Brand: IBM Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands