National Instruments NI PXIe-8103 User Manual Download Page 19

Page: 19 / 75

Chapter 2

Installation and Configuration

National Instruments Corporation

2-3

NI PXIe-8103 User Manual

10. Connect the keyboard and mouse to the appropriate connectors. If you

are using a PS/2 keyboard and a PS/2 mouse, a Y-splitter adapter is
available to connect both to a single USB connector. Refer to
Figure 4-1,

Y-Splitter Cable

11. Connect the VGA monitor video cable to the VGA connector.

12. Connect devices to ports as required by your system configuration.

13. Power on the chassis.

14. Verify that the controller boots. If the controller does not boot, refer

to the

What if the NI PXIe-8103 does not boot?

section of Chapter 5,

Troubleshooting

Figure 2-2 shows an NI PXIe-8103 installed in the system controller slot of
a National Instruments PXIe-1062 chassis.

Figure 2-2.

NI PXIe-8103 Controller Installed in a PXI Express Chassis

PXIe-1062 Chassis

NI PXIe-8103 Controller

Injector/Ejector Rail

NI PXIe-1062

NI PXIe-8103

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for NI PXIe-8103












































































Search results

Summary of Contents for NI PXIe-8103

Reviews:

Related manuals for NI PXIe-8103

Brands by name

Popular brands

National Instruments NI PXIe-8103, User Manual

Search results

Summary of Contents for NI PXIe-8103

Reviews:

Related manuals for NI PXIe-8103

Brands by name

Popular brands