National Instruments NI PXIe-8103 User Manual Download Page 29

Page: 29 / 75

Chapter 2

Installation and Configuration

National Instruments Corporation

2-13

NI PXIe-8103 User Manual

Figure 2-4.

Multichassis Configuration in MAX

PXI-1 System Configuration

Launch MAX.

In the

Configuration

tree, click the

Devices and Interfaces

branch to

expand it.

If the PXI system controller has not yet been configured, it is labeled

PXI System (Unidentified)

. Right-click this entry to display the

pop-up menu, then select the appropriate controller model from the

Identify As

submenu.

Click the

PXI System

controller. The chassis (or multiple chassis, in a

multichassis configuration) is listed below it. Identify each chassis by
right-clicking its entry, then selecting the appropriate chassis model
through the

Identify As

submenu. Further expanding the

PXI System

branch shows all devices in the system that can be recognized by
NI-VISA. When your controller and all your chassis are identified,
the required

pxisys.ini

file is complete.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for NI PXIe-8103












































































Search results

Summary of Contents for NI PXIe-8103

Reviews:

Related manuals for NI PXIe-8103

Brands by name

Popular brands

National Instruments NI PXIe-8103, User Manual

Search results

Summary of Contents for NI PXIe-8103

Reviews:

Related manuals for NI PXIe-8103

Brands by name

Popular brands