background image

Refer to the 

LabVIEW Installation Guide

 for installation instructions for LabVIEW and

system requirements for LabVIEW software. Refer to the 

LabVIEW Upgrade Notes

 for

additional information about upgrading to the most recent version of LabVIEW for
Windows.

3.

(Recommended) Install NI LabVIEW FPGA Module.

Refer to the 

LabVIEW FPGA Module Release and Upgrade Notes

 for installation

instructions and information about getting started with the LabVIEW FPGA Module.

Note

 

Installation of the LabVIEW FPGA Module is required to customize the

device FPGA using the instrument design libraries.

4.

(Recommended) Install the latest service pack for LabVIEW and any LabVIEW modules
you are using.

5.

Insert the driver software DVD into the DVD drive.

The driver software installer should open automatically. If the installation window does
not appear, navigate to the DVD drive, double-click the drive, and double-click

autorun.exe

.

Note

 

You can also download the software from 

ni.com/downloads

.

6.

Follow the instructions in the installation prompts to install the default installation.

Windows users may see access and security messages during installation. Accept the
prompts to complete the installation.

Note

 

The default installation installs NI LabVIEW Instrument Design

Libraries for IF Digitizers, documentation, and device specifications.

Note

 

For troubleshooting information, contact NI technical support or visit 

ni.com/support

.

7.

When the installer completes, restart your system.

Installing the NI 5624R

Caution

 

To prevent damage to the device caused by ESD or contamination, handle

the device using the edges or the metal bracket.

NI recommends installing the software before installing the hardware.

Before you install the hardware, refer to the guidelines in the 

Maintain Forced-Air Cooling

Note to Users

 included with the module to ensure that the device can cool itself effectively.

This document is also available at 

ni.com/manuals

.

1.

Ensure the AC power source is connected to the chassis before installing the NI 5624R.

The AC power cord grounds the chassis and protects it from electrical damage while you
install the NI 5624R.

2.

Power off the chassis.

NI PXIe-5624R Getting Started Guide

  | 

© National Instruments

  | 

5

Summary of Contents for NI PXIe-5624R















Reviews: