background image

© 

National Instruments Corp.

11

FP-CTR-502 and cFP-CTR-502

Output Mode

For each output channel select one of the following output modes 
from the Value menu: 

Toggle, Reset Off

Toggle, Reset On

On Pulse

; or 

Off Pulse

. The output modes work only if you select 

Counter Channel 0–7

 for the 

Output Source

. The following 

sections describe the different output modes.

Toggle, Reset Off

In Toggle, Reset Off mode, the output channel starts low and goes 
high when the terminal count is exceeded. The output channel 
returns to low the next time the terminal count is exceeded or when 
you send a reset command to the associated count-input channel. 
In Figure 7, the terminal count is 4.

Figure 7.  

Output of a Channel Set to Toggle, Reset Off Mode

Toggle, Reset On

In Toggle, Reset On mode, the output channel starts high and goes 
low when the terminal count is exceeded. The output channel 
returns to high the next time the terminal count is exceeded or 
when you send a reset command to the associated count-input 
channel. In Figure 8, the terminal count is 4.

Figure 8.  

Output of a Channel Set to Toggle, Reset On Mode

0

1

2

3

4

0

1

2

3

4

0

1

Output

Count

Input

0

1

2

3

4

0

1

2

3

4

0

1

Output

Count

Input

Summary of Contents for FieldPoint FP-CTR-502
























Reviews: