background image

© 

National Instruments Corp.

9

FP-CTR-502 and cFP-CTR-502

to Channel 0, Channel 0 to Channel 7, Channel 7 to Channel 6, 
and so on. If you select this option for all of the channels, no 
counting occurs.

Gate Source

Select 

Gate Input 0–3

 from the Value menu to associate a 

gate-input channel with a count-input channel. If the count-input 
channel uses one of the external gate inputs, counting is enabled 
when the gate-input signal is high and is disabled when the signal 
is low, as shown in Figure 6. The gate-input signal is high when the 
channel is ON. The external device determines the high and low 
intervals of the gate-input signal. If you do not associate a 
gate-input channel with the count-input channel, select 

Always 

Disabled

 or 

Always Enabled

. Select 

Always Enabled

 if you want 

the count-input channel to count at all times, even if there is 
nothing wired to the gate input. Always Enabled is the default 
value.

Figure 6.  

Gate Source Set to External Gate Input

Read Reset Mode

You can configure each count-input channel to reset each time the 
FieldPoint network module reads it by selecting 

Reset on Read

 

from the Value menu. A read-initiated reset also resets any outputs 
associated with the target channel. The default is Don’t Reset 
On Read.

Note

Read Reset mode is not intended to be used with 

FieldPoint Ethernet network modules.

0

0

1

2

3

3

3

3

4

5

6

6

Gate

Input

Count

Input

Summary of Contents for FieldPoint FP-CTR-502
























Reviews: