NARGESA MP1400 CNC Instruction Booklet Download Page 11

Page: 11 / 77

INSTRUCTIONS BOOK FOR PRESS BRAKE MP1400 CNC 10

3. MAINTENANCE

3.1. General maintenance

At the top of the tank there is the level sightglass. In the absence of oil, fill up to the mark of the peephole.

- Every 1000 hours of use, check the oil level in the tank.

- Replace oil every 4,000 hours of work.

Oil Type: CEPSA HYDRAULIC HM 68

WARNING

Stop the machine in order to carry out the maintenance of the machine. In case of replacement of the oil,
start the engine and depress the flashing time increasing the pressure gradually until the circuit is comple-
te.

- Grease the boulders fixing rods and piston periodically depending on use.

- If the use is daily and continuous, grease each month.

- Grease all guide fittings monthly.

- Check the oil level of the machine.

Oil level dipstick

Filling cap

Emptying cap

Summary of Contents for MP1400 CNC














































































Search results

Summary of Contents for MP1400 CNC

Reviews:

Brands by name

Popular brands

NARGESA MP1400 CNC, Instruction Booklet

Search results

Summary of Contents for MP1400 CNC

Reviews:

Brands by name

Popular brands