Narex ASR 600-3MTB BASIC, Original Operating Manual

Page: 21 / 68

21
English
5� If you are carrying out several different charge operations one
after the other, the charger may become hot� This is normal
and is not a sign of a technical problem�
6� Prevent liquid from getting inside the charger as it could cause
an electrical injury� Do not place the battery in a hot environ-
ment if you wish to facilitate the battery cool down process�
7� Accumulator batteries can remain plugged into the charger
without a risk of damage to them or the charger itself� The bat-
teries will remain fully charged in the charger� DO NOT LEAVE
charged batteries in the charger if the charger is not plugged
into the power outlet�
8�
DO NOT USE ACCUMULATOR BATTERIES
if they are damaged
or if liquid leaks out of the cells� If the battery liquid comes
into contact with your skin, immediately flush the area with
water and monitor the skin’s reaction� Seek medical attention
if needed� If it comes into contact with your eyes, flush them
with lots of water and immediately seek medical attention�
9� If you are charging a fully discharged battery or if you stop
charging the battery before it is fully charged, you must count
each of these cycles as an entire charging cycle�
Note on Lithium-ion (Li-Ion) batteries
• These types of batteries do not have a memory effect, in other
words, the batteries can be charged at any state of discharge� If
you take the batteries out of the charger prior to fully charging
them, it will not damage them�
• Each Li-Ion battery is equipped with deep discharge protec-
tion� If the voltage falls (due to overloading or discharge) be-
low the monitored range, the electronic circuit will disconnect
the cells� The machine will then either work intermittently or
not at all� You must reduce machine load or recharge the bat-
tery�
Storing lithium-ion batteries
• Store fully charge batteries in a dry and dust-free environment
at an ambient temperature between 5 °C and 40 °C� If you are
not using the batteries for a longer period of time, we recom-
mend you charge them fully once every three months�
• Keep the battery contacts clean� Do not store the replacement
battery together with metal items as it may cause a short cir-
cuit�
• It is always necessary to charge batteries that were not used for
a long time prior to use�
Transporting lithium-ion batteries
As per legal regulation, lithium-ion batteries fall into the hazard-
ous load category� These batteries must be transported while com-
plying with local, national, as well as international guidelines and
regulations�
• Consumers may transport these batteries on public roads with-
out a problem�
• Commercial transportation of lithium-ion batteries by trans-
portation companies must comply with the regulation on
hazardous load transportation� Only trained personnel may
carry out the preparation and the actual transport� The entire
process must have expert supervision�
The following must be maintained during battery transpor-
tation:
• Make sure that contacts are protected and isolated to prevent
a short circuit�
• Be careful so that a large number of batteries do not move
around or fall and collapse during transport�
• Damaged and leaking batteries cannot be transported�
Please contact your carrier for additional information�
Warning!!
It is not expected for the user to perform any service repairs on the
charger� There are no spare parts inside the charger, which users
could repair on their own� It is necessary to bring the charger to
your nearest authorised service centre to prevent damage to spare
parts, which are sensitive to static electricity, for example�
Always use the right set of batteries (the set delivered with the
tools or a replacement set recommended by Narex s�r�o�)� Never
use any other sets of accumulator batteries because they could
damage your tools and cause a hazardous situation�
Function principle
A spindle with the tool is powered by an electric motor with a
transmission and an impact mechanism�
The work process is divided into two phases:
1� Driving a screw
2� Tightening (the impact mechanism is activated)
The impact mechanism is activated only once the screw joint
is fixed – the motor is engaged� The impact mechanism thereby
changes the power of the motor to even the rotary impacts�
This process is reversed when loosening screws�
Instructions for use
Mount the device, which must be turned off, onto a nut/screw.
The torque depends on how long the impacts last� Maximum
torque is based on individual torques reached by the impacts� The
maximum torque is reached once the impacts last for about 3 to 5
seconds� From this moment on, the torque increases only slightly;
however, it noticeably heats the impact mechanism� Overheating
wears down the impact spare parts and uses up higher amounts
of lubrication�
The impact period must be designated for each required torque�
The actual tightening torque reached must be continuously veri-
fied using a torque key�
The default status of the screw joint and its technical specification
is always an important factor for reaching the tightening or loosen-
ing device performance�
There are two typical joints to be used:
Hard joint:
Using a screw joint to tighten two or more (usually) steel parts,
which do not flex, nor are they deformed in any way as a result of
tightening pressure�
Soft joint:
Using a screw joint to tighten two or more parts, where at least
one part is from such material or is made in such a way that the
tightening pressure deforms or flexes it�
Commissioning
Inserting and removing a battery
Insert the battery (1) into the shaft on the bottom side of the ma-
chine handle all the way� Pull on the battery to make sure it is fitted
properly�
To remove a battery (1) from the machine, push on both battery
clamps (2) and pull the battery out�
Turning the device ON
Pressing on the switch button (3) and gradually pushing on it will
regulate speed� If you press the switch button (3), the LED work
areal light (7) will automatically switch on� It is used to light up the
work space directly in front of the machine – clamped device�
Turning the device OFF
Release the switch button (3)� The rundown of the spindle is de-
creased using the brake after being turned off�
Lower speed is suitable for guiding the nut/bolt�
ATTENTION! Long-term use of variable rotation speeds
is not recommended. It can lead to switch button dam-
age.
Changing the rotation direction
Using the turn direction switch (4) changes the rotation direction:
• Push down from right to left – clockwise�
• Push down from left to right – counter-clockwise�
• Button is in between – protection against accidental start�