background image

6.0  operation

31.1A

!

WARNING

•  Do not turn on if children or other at risk individuals are near the appliance.

•  This appliance is equipped with a pilot which must be lit by hand while following these instructions exactly.

•  Before operating, smell all around the appliance area for gas and next to the fl oor because some gas is heavier 

than air and will settle on the fl oor.

•  Use only your hand to turn the gas control knob. Never use tools. If the knob will not turn by hand, do not try 

to repair it. Call a qualifi ed service technician. Force or attempted repair may result in a fi re or explosion.

•  Do not use this appliance if any part has been under water. Immediately call a qualifi ed service technician 

to inspect the appliance and replace any part of the control system and any gas control which has been 

underwater.

FOR YOUR SAFETY READ BEFORE LIGHTING

WHAT TO DO IF YOU SMELL GAS

LIGHTING INSTRUCTIONS

TO TURN OFF GAS

A.

  Stop! Read the above safety information on this label.

B.

  Remove batteries from the transmitter and set thermostat to lowest setting, if equipped.

C.

  Turn off all electrical power to the appliance.

D.

  Open the glass door, if equipped.

E.

  Turn the gas knob clockwise            to the “OFF” position. 

F.

  Wait fi ve (5) minutes to clear out any gas. If you smell gas including near the fl oor, STOP! 

Follow the instructions above in the “WHAT TO DO IF YOU SMELL GAS” section. If you 

don’t smell gas; close the glass door and go to the next step.

G.

  If the appliance is equipped with fl ame adjustment valve turn clockwise            to “OFF”.

H.

  Turn gas knob counter-clockwise          to the “PILOT” position. (If the appliance is equipped 

with an “ON/OFF” switch, ensure it is in the “ON” position.

I.

  Depress and hold gas knob while lighting the pilot with the push button ignitor. Keep knob 

fully depressed for one minute, then release. If pilot does not continue to burn, repeat steps 

E through I.

J.

  With pilot lit, turn gas knob counter-clockwise 

 to the “ON” position.

K.

  If equipped with the fl ame adjustment valve, push and turn the knob to high.

L.

  Turn on all electrical power to the appliance and re-install the batteries into the transmitter, if 

equipped. Set thermostat to desired setting, if equipped.

A.

  Set thermostat to desired setting, if equipped.

B.

  Turn off all electrical power to the appliance if service is to be performed.

C.

  Push in gas knob slightly and turn clockwise            to the “OFF” position. Do not force.

•  Turn off all gas to the appliance.

•  Open windows.

•  Do not try to light any appliance.

•  Do not touch any electric switch; do not use 

any phone in your building

•  Immediately call your gas supplier from a 

neighbour’s phone. Follow the gas supplier’s 

instructions.

•  If you cannot reach your gas supplier, call 

the fi re department.

•  If you do not follow these instructions exactly, a fi re or explosion may result causing property damage, personal 

injury, or loss of life.

•  If applicable, always light the pilot whether for the fi rst time or if the gas supply has run out with the glass door 

opened or removed.

add gas knob

add gas valve

Ensure that a continuous gas fl ow is at the burner before installing the door. When lit for the fi rst time, the appliance 

will emit an odor for a few hours. This is a normal temporary condition caused by the “burn-in” of paints and 

lubricants used in the manufacturing process and will not occur again. After extended periods of non-operation 

such as following a vacation or a warm weather season, the appliance may emit a slight odor for a few hours. This 

is caused by dust particles in the heat exchanger burning off. In both cases, open a window to suffi ciently ventilate 

the room.

For vent free appliances ONLY:

 if the appliance shuts off, do not relight until you provide fresh air. If appliance 

keeps shutting off, have it serviced. Keep burner and control compartment clean.

note:

When lighting and re-lighting, the gas knob cannot be turned from pilot to off unless the knob is 

depressed.

22

W415-0379 / E / 04.24.12

FOR YOUR SAFETY READ BEFORE LIGHTING:

Ɣ

  This appliance is equipped with a pilot which must be lit by hand while following these instructions exactly.

Ɣ

Before operating smell all around the appliance area for gas and next to the floor because some gas is heavier than air and will settle on the floor.

Ɣ

   Use only your hand to push in and turn the gas control knob. Never use tools. If the knob will not push in and turn by hand, do not try 

     to repair it. Call a qualified service technician. Force or attempted repair may result in a fire or explosion.

Ɣ

  Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance

     and replace any part of the control system and any gas control which has been under water.

Ɣ

Do not try to light any appliance.

Ɣ

Do not touch any electric switch; do not use any phone in your building.

Ɣ

   Immediately call your gas supplier from a neighbour’s phone. Follow the gas supplier’s instructions.

Ɣ

   If you cannot reach your gas supplier, call the fire department.

When lighting and re-lighting, the gas knob cannot be turned from pilot to off unless the knob is depressed.

$

  STOP! Read the above safety information on this label.

%

  Set the thermostat to lowest setting.

&

  Turn off all electric power to the appliance.

'

 Open the control door. Turn the gas knob clockwise to off.

(

  Wait five (5) minutes to clear out any gas. If you smell gas including near the floor, STOP! Follow “B” in the above safety information

      on this label. If you don’t smell gas go to the next step.

)

  Find pilot located in front of the back log.

G.

   Turn gas knob counter-clockwise to pilot.

H.

   Depress and hold gas knob while lighting the pilot with the push button ignitor. Keep knob fully depressed for one minute, then

      release. If pilot does not continue to burn repeat steps 3 through 7.

,

  With pilot lit, turn gas knob counter-clockwise  to on. When the pilot has been turned off, 

      ignition of the main burner may be delayed from 1-2 minutes. When the pilot has been left 

      burning, ignition of the main burner should occur almost immediatley.

-

  If equipped with remote on-off switch, main burner may not come on when you turn the valve to on. Remote switch must be in 

      the on position to ignite burner.

K.

  Turn on all electric power to the appliance.

A.

   Turn off all electric power to the appliance if service is to be performed.

%

Push in gas control knob slightly and turn clockwise to off. Do not force.

WHAT TO DO IF YOU SMELL GAS:

LIGHTING INSTRUCTIONS:

TO TURN OFF GAS

,IDSSOLDQFHVKXWVRIIGRQRWUHOLJKWXQWLO\RXSURYLGHIUHVKDLU,IDSSOLDQFHNHHSVVKXWWLQJRIIKDYHLWVHUYLFHG.HHSEXUQHU

DQGFRQWUROFRPSDUWPHQWFOHDQ

When lit for the first time, the appliance will emit a slight odour for a few hours. This is a normal temporary condition caused by the curing 

of the logs and the “burn-in” of internal paints and lubricants used in the manufacturing process and will not occur again. After extended 

periods of non-operation such as following a vacation or a warm weather season, the appliance may emit a slight odour for a few hours. 

This is caused by dust particles burning off. In both cases, open a window to sufficiently ventilate the room.

47.1

,)<28'2127)2//2:7+(6(,16758&7,216(;$&7/<$),5(25(;3/26,210$<5(68/7

&$86,1*3523(57<'$0$*(3(5621$/,1-85<25/2662)/,)(

,)$33/,&$%/($/:$<6/,*+77+(3,/27:+(7+(5)257+(),5677,0(25,)7+(*$66833/<+$6

581287:,7+7+(*/$66'22523(1('255(029('

!

WARNING

7.0 OPERATION

22

W415-0379 / E / 04.24.12

FOR YOUR SAFETY READ BEFORE LIGHTING:

Ɣ

  This appliance is equipped with a pilot which must be lit by hand while following these instructions exactly.

Ɣ

Before operating smell all around the appliance area for gas and next to the floor because some gas is heavier than air and will settle on the floor.

Ɣ

   Use only your hand to push in and turn the gas control knob. Never use tools. If the knob will not push in and turn by hand, do not try 

     to repair it. Call a qualified service technician. Force or attempted repair may result in a fire or explosion.

Ɣ

  Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance

     and replace any part of the control system and any gas control which has been under water.

Ɣ

Do not try to light any appliance.

Ɣ

Do not touch any electric switch; do not use any phone in your building.

Ɣ

   Immediately call your gas supplier from a neighbour’s phone. Follow the gas supplier’s instructions.

Ɣ

   If you cannot reach your gas supplier, call the fire department.

When lighting and re-lighting, the gas knob cannot be turned from pilot to off unless the knob is depressed.

$

  STOP! Read the above safety information on this label.

%

  Set the thermostat to lowest setting.

&

  Turn off all electric power to the appliance.

'

 Open the control door. Turn the gas knob clockwise to off.

(

  Wait five (5) minutes to clear out any gas. If you smell gas including near the floor, STOP! Follow “B” in the above safety information

      on this label. If you don’t smell gas go to the next step.

)

  Find pilot located in front of the back log.

G.

   Turn gas knob counter-clockwise to pilot.

H.

   Depress and hold gas knob while lighting the pilot with the push button ignitor. Keep knob fully depressed for one minute, then

      release. If pilot does not continue to burn repeat steps 3 through 7.

,

  With pilot lit, turn gas knob counter-clockwise  to on. When the pilot has been turned off, 

      ignition of the main burner may be delayed from 1-2 minutes. When the pilot has been left 

      burning, ignition of the main burner should occur almost immediatley.

-

  If equipped with remote on-off switch, main burner may not come on when you turn the valve to on. Remote switch must be in 

      the on position to ignite burner.

K.

  Turn on all electric power to the appliance.

A.

   Turn off all electric power to the appliance if service is to be performed.

%

Push in gas control knob slightly and turn clockwise to off. Do not force.

WHAT TO DO IF YOU SMELL GAS:

LIGHTING INSTRUCTIONS:

TO TURN OFF GAS

,IDSSOLDQFHVKXWVRIIGRQRWUHOLJKWXQWLO\RXSURYLGHIUHVKDLU,IDSSOLDQFHNHHSVVKXWWLQJRIIKDYHLWVHUYLFHG.HHSEXUQHU

DQGFRQWUROFRPSDUWPHQWFOHDQ

When lit for the first time, the appliance will emit a slight odour for a few hours. This is a normal temporary condition caused by the curing 

of the logs and the “burn-in” of internal paints and lubricants used in the manufacturing process and will not occur again. After extended 

periods of non-operation such as following a vacation or a warm weather season, the appliance may emit a slight odour for a few hours. 

This is caused by dust particles burning off. In both cases, open a window to sufficiently ventilate the room.

47.1

,)<28'2127)2//2:7+(6(,16758&7,216(;$&7/<$),5(25(;3/26,210$<5(68/7

&$86,1*3523(57<'$0$*(3(5621$/,1-85<25/2662)/,)(

,)$33/,&$%/($/:$<6/,*+77+(3,/27:+(7+(5)257+(),5677,0(25,)7+(*$66833/<+$6

581287:,7+7+(*/$66'22523(1('255(029('

!

WARNING

7.0 OPERATION

22

W415-0379 / E / 04.24.12

FOR YOUR SAFETY READ BEFORE LIGHTING:

Ɣ

  This appliance is equipped with a pilot which must be lit by hand while following these instructions exactly.

Ɣ

Before operating smell all around the appliance area for gas and next to the floor because some gas is heavier than air and will settle on the floor.

Ɣ

   Use only your hand to push in and turn the gas control knob. Never use tools. If the knob will not push in and turn by hand, do not try 

     to repair it. Call a qualified service technician. Force or attempted repair may result in a fire or explosion.

Ɣ

  Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance

     and replace any part of the control system and any gas control which has been under water.

Ɣ

Do not try to light any appliance.

Ɣ

Do not touch any electric switch; do not use any phone in your building.

Ɣ

   Immediately call your gas supplier from a neighbour’s phone. Follow the gas supplier’s instructions.

Ɣ

   If you cannot reach your gas supplier, call the fire department.

When lighting and re-lighting, the gas knob cannot be turned from pilot to off unless the knob is depressed.

$

  STOP! Read the above safety information on this label.

%

  Set the thermostat to lowest setting.

&

  Turn off all electric power to the appliance.

'

 Open the control door. Turn the gas knob clockwise to off.

(

  Wait five (5) minutes to clear out any gas. If you smell gas including near the floor, STOP! Follow “B” in the above safety information

      on this label. If you don’t smell gas go to the next step.

)

  Find pilot located in front of the back log.

G.

   Turn gas knob counter-clockwise to pilot.

H.

   Depress and hold gas knob while lighting the pilot with the push button ignitor. Keep knob fully depressed for one minute, then

      release. If pilot does not continue to burn repeat steps 3 through 7.

,

  With pilot lit, turn gas knob counter-clockwise  to on. When the pilot has been turned off, 

      ignition of the main burner may be delayed from 1-2 minutes. When the pilot has been left 

      burning, ignition of the main burner should occur almost immediatley.

-

  If equipped with remote on-off switch, main burner may not come on when you turn the valve to on. Remote switch must be in 

      the on position to ignite burner.

K.

  Turn on all electric power to the appliance.

A.

   Turn off all electric power to the appliance if service is to be performed.

%

Push in gas control knob slightly and turn clockwise to off. Do not force.

WHAT TO DO IF YOU SMELL GAS:

LIGHTING INSTRUCTIONS:

TO TURN OFF GAS

,IDSSOLDQFHVKXWVRIIGRQRWUHOLJKWXQWLO\RXSURYLGHIUHVKDLU,IDSSOLDQFHNHHSVVKXWWLQJRIIKDYHLWVHUYLFHG.HHSEXUQHU

DQGFRQWUROFRPSDUWPHQWFOHDQ

When lit for the first time, the appliance will emit a slight odour for a few hours. This is a normal temporary condition caused by the curing 

of the logs and the “burn-in” of internal paints and lubricants used in the manufacturing process and will not occur again. After extended 

periods of non-operation such as following a vacation or a warm weather season, the appliance may emit a slight odour for a few hours. 

This is caused by dust particles burning off. In both cases, open a window to sufficiently ventilate the room.

47.1

,)<28'2127)2//2:7+(6(,16758&7,216(;$&7/<$),5(25(;3/26,210$<5(68/7

&$86,1*3523(57<'$0$*(3(5621$/,1-85<25/2662)/,)(

,)$33/,&$%/($/:$<6/,*+77+(3,/27:+(7+(5)257+(),5677,0(25,)7+(*$66833/<+$6

581287:,7+7+(*/$66'22523(1('255(029('

!

WARNING

7.0 OPERATION

W415-0379 / F / 06.11.18

EN

 

24

  

Summary of Contents for GVF42-1N



































Reviews: