Napoleon GVF42-1N Installation And Operation Manual Download

Page: 1 / 34

ADD MANUAL TITLE

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 0G8 Canada / 103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone 1 (866) 820-8686 • www.continentalfi replaces.com • ask@continentalfi re.on.ca

CERTIFIED TO THE AMERICAN NATIONAL STANDARD:

ANSI _______ FOR _____________________________________________________

INSTALLER:

Leave this manual with the appliance

CONSUMER:

Retain this manual for future reference

ADD PRODUCT CODE HERE (TRADE GOTHIC LT STD FONT)

NATURAL GAS MODELS:

PROPANE GAS MODELS:

Product Name / Code

(see price book)

ADD ____ ILLUSTRATED

ADD PRODUCT IMAGE

CERTIFICATION

LOGO

SAFETY INFORMATION

- Do not store or use gasoline or other

fl ammable vapors and liquids in the vicinity of

this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not

use any phone in your building.

• Immediately call your gas supplier from a

neighbour’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier, call

the fi re department.

- Installation and service must be

performed by a qualifi ed installer, service

agency, or the supplier.

- This is an unvented gas-fi red heater that

uses air (oxygen) from the room in which

it is installed. Provisions for adequate

combustion and ventilation air must be

provided. Refer to section “combustion

and ventilation air provisions”.

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA

only) or mobile home, where not prohibited by

local codes.
This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless

a certifi ed kit is used.

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly

could result in serious injury, death, or

property damage.

WARNING

ENGLISH

$10.00

FOR INDOOR USE ONLY

IF INSTAL OPERATION, ADD SERIAL

NUMBER LABEL HERE

IF SEPARATE MANUALS, ADD “PLACE

BARCODE LABEL ON THE OWNER’S MANUAL”

GVF42-1P

GVF42-1N

INSTALLATION AND

OPERATION MANUAL

Grandville™ Vent Free Series

CERTIFIED TO THE AMERICAN NATIONAL STANDARDS:

ANSI Z21.11.2, VOLUME II FOR UNVENTED ROOM HEATERS.

W415-0379 / F / 06.11.18

Summary of Contents for GVF42-1N



































Search results

Summary of Contents for GVF42-1N

Reviews:

Related manuals for GVF42-1N

Brands by name

Popular brands

Napoleon GVF42-1N, Installation And Operation Manual

Search results

Summary of Contents for GVF42-1N

Reviews:

Related manuals for GVF42-1N

Brands by name

Popular brands