X
GEM-P3200 Installation Instructions
L
NAPCO Security Systems
WI817F 10/05
Page 36
Zone 1 is “E,1”. The communicator will send “123 E” (Account No. 123 Restored); followed by “EEE 1” (Restored, Zone 1).
Modem Formats.
Modem formats (SIA, Point ID, Express, 4/3/1, Modem 2) are preset and automatic but require a Type for
each zone. Program Zone Type as follows: Fire* = “1” (Note: Not for Modem 2 Receivers); Panic = “2”; Burglary = “3”;
Holdup = “4”; Gas Alarm = “7”; Heat Alarm = “8”; Auxiliary Alarm = “A” (Keypad displays “0”); 24-Hour Aux. Alarm = “B”.
Pager Formats.
The control panel has provisions for dialing a pager phone number. The panel will wait for ringing, wait for si-
lence, then send its data. Caution: Because there is no handshake/kissoff, this feature should only be used for Double Re-
porting; it may not be used for Backup Reporting. Only one report is sent for any call. Pager digits are limited to “0” through
“9”. Digits represented by “A” through “F” will be converted to “0”s for transmission purposes. Pager formats are 10 digits, ar-
ranged as illustrated by the following examples.
Alarms, restores, etc. are transmitted in a 3-3-4 arrangement representing Report Code, Descriptor and Account Number.
Example 1. Burglary, Zone 22 (Report Code = “3”.)
Transmits: 003 022 1234, where
003 = Report Code (always two zeros + programmable Report-Code digit, 0–9);
022 = Descriptor (always one zero + 2-digit descriptor, zone number: 01–96);
1234 = Account Number (4 digits, programmable).
Openings, closings, etc. are transmitted in a similar arrangement
Example 2. Closing, User 12 (Closing Code = “8”)
Transmits 008 012 1234, where
008 = Report Code (always two zeros + programmable Opening/Closing digit, 0–9)
012 = Descriptor (always one zero + 2-digit descriptor (user number: 01–96);
1234 = Account Number (4 digits, programmable).
Keypad Report Codes and System Report Codes are transmitted in the same format.
Pager - Programmable Number of Resends of Report
Program the number of resends to allow the panel to send multi-
ple reports of same signal to insure that signal is received by pager.
Pager - Maximum number of reports per session.
Program the maximum number of Pager reports to be sent per ses-
sion.
Pager (Telco 3) Report Delay
Programmable delay of the Telco 3 report (typically used for Pager Reporting) intended to
allow time for central station to to allow to verify alarm report the alarm report.
Compatible Receivers.
The following receivers are compatible with the GEM-P3200.
•
FBI CP220.
Formats: Ademco Slow; Silent Knight Slow; Silent Knight Fast; Sescoa; Vertex; DCI; Franklin Slow;
Franklin Fast; SIA; Radionics Slow; Radionics Fast; Radionics BFSK; FBI 4/3/1; Universal High Speed.
•
Ademco 685.
Formats: Ademco Slow; Silent Knight Slow; Silent Knight Fast; Sescoa; Vertex; DCI; Franklin Slow;
Franklin Fast; Radionics Slow; Radionics Fast; Radionics BFSK; Universal High Speed; Ademco Point ID; Ademco
Express.
•
Radionics 6500.
Formats: Ademco Slow; Silent Knight Slow; Silent Knight Fast; Sescoa; Vertex; DCI; Franklin Slow;
Franklin Fast; Radionics Slow; Radionics Fast; Radionics BFSK; Universal High Speed; Radionics Modem 2.
•
Osborne-Hoffman Quickalert.
Formats: Ademco Slow; Silent Knight Slow; Silent Knight Fast; Sescoa; Vertex; DCI;
Franklin Slow; Franklin Fast; SIA; Radionics Slow; Radionics BFSK; Universal High Speed; Ademco Point ID; Ademco
Express.
•
Silent Knight 9000.
Formats: Ademco Slow; Silent Knight Slow; Silent Knight Fast; Sescoa; Vertex; DCI; Franklin
Slow; Franklin Fast; Radionics Slow; Radionics Fast; Radionics BFSK; Universal High Speed; SIA.
Day Zone(Open; Short)
Alarm on Day Zone
Disable Auto-Reset on Day Zone
Reset Day Zone with Arm/Disarm Only
Enable Watch, Areas 1-8
(By Area)
A Day Zone will give an audible and visual indication at the keypad if there is a problem on the loop while disarmed. Open- and
short-circuit conditions are programmed separately, by zone. This feature may be used to warn of a problem (a break in a window
foil, for example) during the day, when the panel is not normally armed. When the Day Zone is tripped, “
DAY ZONE TRBL
” and the zone
number(s) will alternately display at the keypad and the sounder will pulse. Press the
C
button to silence the sounder and reset
the keypad. “
ZONE FAULT
” will be displayed until the condition is corrected. If Reset Day Zone With Arm/Disarm Only is programmed,
arm and disarm the panel to reset the Day-Zone indication at the keypad.
If Alarm on Day Zone is programmed for a zone, a Day Zone condition will cause the alarm outputs programmed for that zone
(sirens, relays) to activate.
Note:
(1) If a zone is programmed for both Day Zone Open and Day Zone Short, either condition must be reset before the other
can activate. (2) Day Zone Short will not function if No EOL Resistor is also programmed.
Report Trouble or Trouble Restore is programmed in conjunction with Day Zone Open/Day Zone Short and Trouble on Open/
Trouble on Short (the trouble reported will be that programmed under Day Zone Open and/or Day Zone Short).
Note:
Do not program a Day Zone for 24-hour protection. The keypad will annunciate as a Day Zone but the panel will transmit
an Alarm Code and a Trouble Code when tripped.
Program Disable Auto-Reset on Day Zone to prevent repeated Day-Zone trips. This will cause the keypad display and sounder
to activate only once in any arm/disarm period.
If Enable Watch is selected (by area), zones programmed for Day Zone can only be activated when ACTIVATE WATCH is ac-
GLOSS
A
RY
Summary of Contents for Gemini GEM-P3200
Page 58: ...X GEM P3200 Installation Instructions L NAPCO Security Systems WI817F 10 05 Page 58 NOTES...
Page 66: ...X GEM P3200 Installation Instructions L NAPCO Security Systems WI817F 10 05 Page 66 Notes...
Page 67: ...L NAPCO Security Systems X GEM P3200 Installation Instructions WI817F 10 05 Page 67 Notes...
