background image

791-7332 

rev. 03/23/18

WARNING INFORMATION

This is the safety alert symbol. It is used to alert you 
to potential personal injury hazards. Obey all safety 
messages that follow this symbol to avoid possible 
injury or death.

            IMPORTANT: READ THESE INSTRUCTIONS BEFORE OPERATING

BEFORE USING THIS DEVICE, READ THIS MANUAL COMPLETELY AND THOROUGHLY, UNDERSTAND ITS OPERATING PROCEDURES, SAFETY 
WARNINGS AND MAINTENANCE REQUIREMENTS.

It is the responsibility of the owner to make sure all personnel read this manual prior to using the device. It is also the responsiblity of the device owner 
to keep this manual intact and in a convenient location for all to see and read. If the manual or product labels are lost or not legible, contact NAPA 
for replacements. If the operator is not fluent in English, the product and safety instructions shall be read to and discussed with the operator in the 
operator's native language by the purchaser/owner or his designee, making sure that the operator comprehends its contents.

THE NATURE OF HAZARDOUS SITUATIONS

The use of portable automotive lifting devices is subject to certain hazards that cannot be prevented by mechanical means, but only by the exercise of 
intelligence, care, and common sense. It is therefore essential to have owners and personnel involved in the use and operation of the equipment who 
are careful, competent, trained, and qualified in the safe operation of the equipment and its proper use. Examples of hazards are dropping, tipping 
or slipping of loads caused primarily by improperly securing loads, overloading, off-centered loads, use on other than hard level surfaces, and using 
equipment for a purpose for which it was not designed.

METHODS TO AVOID HAZARDOUS SITUATIONS

 

• Read, study, understand and follow all instructions before operating this device.

 

• Inspect the jack before each use.  Do not use if damaged, altered, modified, in poor condition, leaking hydraulic fluid or unstable due to  

 

  loose or missing components.  Make corrections before using.

 

• User and bystanders must wear eye protection that meets ANSI Z87.1 and OSHA standards.

 

• Inspect the engine stand before each use.  Do not use if damaged, altered, modified, in poor condition, or has loose or missing  

 

 

  components.  Take corrective action before using the engine stand.

 

• Lift only at points of the vehicle as specified by the vehicle manufacturer.

 

• Do not exceed rated capacity.

 •

 This is a lifting device only.  Immediately after lifting, support the vehicle with jack stands capable of sustaining the load 

 

  before working on the vehicle.

 • 

No persons should be under vehicle when jack is in use.

 

• No alterations shall be made to this product.

 

• Use only on a hard level surface.

 

• Always lower the jack slowly and carefully.

 

• Do not use saddle adaptors or saddle extenders between the stock lifting saddle and the load.

 

• Failure to heed these warnings may result in serious or fatal personal injury and/or property damage.

 

        

WARNING:

 This product can expose you to chemicals including nickel, which is known to the State of California to cause cancer and birth 

        defects or other reproductive harm.  For more information go to www.P65Warnings.ca.gov.

CONSEQUENCES OF NOT AVOIDING HAZARDOUS SITUATIONS

Failure to read this manual completely and thoroughly, failure to understand its OPERATING INSTRUCTIONS, SAFETY WARNINGS, MAINTENANCE 
INSTRUCTIONS and comply with them, and failure to comply with the METHODS TO AVOID HAZARDOUS SITUATIONS could cause accidents resulting 
in serious or fatal personal injury and/or property damage.

WARNING: Indicates a hazardous situation 
which, if not avoided, could result in death 
or serious injury.

WARNING

WARNING

WARNING

WARNING

OPERATING MANUAL & PARTS LIST FOR  791-7332

Summary of Contents for 791-7332














Reviews: