background image

791-7332 

rev. 03/23/18

WARRANTY

Please contact your local NAPA Auto Parts Store for details on warranty.

7.  After the work is done, close the release knob and depress the air valve until the jack is high enough to remove the vehicle or load from the  

  safety support stand saddles. Be sure load is stable. If it is not, lower load back onto safety support stands. Make appropriate setup 
  corrections and repeat the step again. Remove the safety support stands from under the vehicle being very careful not to move the vehicle.

8.  Turn the release knob in a counterclockwise direction very slowly and carefully to lower the vehicle or load down to the ground.

PREVENTATIVE MAINTENANCE

This is the safety alert symbol used for the PREVENTATIVE MAINTENANCE section of this manual to alert you to potential personal  

injury hazards. Obey all instructions to avoid possible injury or death.

1.   Always store the jack in a well protected area where it will not be exposed to inclement weather, corrosive vapors, abrasive dust, or any  

    other harmful elements. The jack must be cleaned of water, snow, sand, grit, oil, grease or other foreign matter before using.

2.   The jack must be lubricated periodically in order to prevent premature wearing of parts. A general purpose grease must be applied to  

    the threads on the extension screw. Do not lubricate any portion of the lift saddle and make sure the saddle is free from grease, any kind  
    of lubricant, or debris before using the jack. Jacks found to be defective due to worn parts resulting from inadequate or no lubrication  
    are not eligible for warranty consideration.

3.   It should not be necessary to refill or top off the reservoir with hydraulic fluid unless there is an external leak. An external leak requires 

    immediate repair which must be performed in a dirt-free environment by an authorized service center.

IMPORTANT:

 In order to prevent seal damage and jack failure, never use alcohol, hydraulic brake fluid or transmission oil in the jack. 

Use NAPA hydraulic Jack Oil #765-1541.

4.   Every jack owner is responsible for keeping the jack labels clean and readable. Use a mild soap solution to wash external surfaces of the  

    jack but not any moving hydraulic components. Contact NAPA for replacement labels if not readable.

5.   Inspect the jack before each use. Do not use the jack if any component is cracked, broken, bent, shows sign of damage or leaks  

    hydraulic fluid. Do not use the jack if it has loose or missing hardware or components, or is modified in any way. Take corrective 
    action before using the jack again.

6.   Any hydraulic repairs within the warranty period must be performed by an authorized service center.

TROUBLESHOOTING

PROBLEM

ACTION

1. Unit will not lift rated load.

Purge air from hydraulic system by following procedure under 
SETUP.

2. Unit will not sustain rated load or feels “spongy” under rated load. Purge air from hydraulic system as above.
3. Unit will not lift to full height.

Purge air from hydraulic system as above.

4. Handle tends to raise up while the unit is under rated load.

Pump the handle rapidly several times to push oil past ball valves in 
power unit.

5. Unit still does not operate.

For a complete list of authorized hydraulic repair centers please 
visit www.toolwarrantyrepair.com.

Summary of Contents for 791-7332














Reviews: