manualshive.com logo in svg

NAL A3LA-RS, General Description Manual, Page: 56 / 101

Share
Download
NAL A3LA-RS General Description Manual Download Page 56

NAL Research Corporation (TN2012-02-V1.0) 

56 

+CSQ: <rssi> 

where <rssi> is: 

0  

Equivalent to 0 bars displayed on the signal strength indicator 

1  

Equivalent to 1 bar displayed on the signal strength indicator 

2  

Equivalent to 2 bars displayed on the signal strength indicator 

3  

Equivalent to 3 bars displayed on the signal strength indicator 

4  

Equivalent to 4 bars displayed on the signal strength indicator 

5  

Equivalent to 5 bars displayed on the signal strength indicator 

Note:

 The +CSQ form of the command waits for an updated signal strength reading to become 

available. This will usually be within two seconds of issuing the command. If the A3LA-RS is in 
the process of acquiring the system, or in a satellite handoff, a delay in response of up to 10 
seconds may be experienced. 

If the A3LA-RS has no SIM, is awaiting a SIM PIN entry, has an invalid SIM, or has otherwise 
not  proceeded  to  successful  registration,  the  delay  in  response  may  exceed  the  50  second 
timeout  limit.  Under  such  condition,  an  ERROR  response  will  be  received.  To  avoid  a  delayed 
response due to registration problems, issue the +CREG command to verify registration prior to 
entering the +CSQ command to obtain signal strength. 

Note:

 The +CSQF form of the command returns immediately, reporting the last known signal 

strength. 

Test Command:

 +CSQ=? 

List the supported signal strength indications. The response is in the form: 

+CSQ: (supported <rssi>s) 

A.8.97  +CULK – Unlock 

Exec Command: 

+CULK=<unlock key> 

Unlock  the  SBD  functionality  of  the  A3LA-RS  after  it  has  been  locked  by  the  Gateway.  The 
unlock key must be obtained by contacting Iridium’s customer support. 
<unlock key>: 

0000000000000000 .. FFFFFFFFFFFFFFFF (a string of 16 hexadecimal digits) 

While the A3LA-RS is locked, it is unable to perform any SBD sessions. Any attempts to start a 
session will return an error code indicating that the A3LA-RS is locked. 

Command Response: 

+CULK:<status>

 

where: 

<status> indicates the lock status of the A3LA-RS following the unlock attempt: 

0  

Unlocked – A3LA-RS is not locked and is permitted to perform SBD sessions. 

1  

Locked  –  A3LA-RS  is  locked  and  unable  to  perform  SBD  sessions.  It  must  be 

unlocked by supplying the correct unlock key to the +CULK command. 

2  

Permanently  locked  –  A3LA-RS  is  locked  and  unable  to  perform  SBD  sessions.  It 
cannot be unlocked and must be returned to the supplier. 

Read Command: 

+CULK? 

Summary of Contents for A3LA-RS






































































































Reviews:

No comments