manualshive.com logo in svg

NAL A3LA-RS, General Description Manual, Page: 42 / 101

Share
Download
NAL A3LA-RS General Description Manual Download Page 42

NAL Research Corporation (TN2012-02-V1.0) 

42 

Exec Command: 

+CMUT=<n> 

This command is used to enable and disable the uplink voice muting during a voice call. <n> 
can take one of the following values: 

0  

mute off 

1  

mute on 

Read Command: 

+CMUT? 

Query the current mute setting. The response is in the form: 

+CMUT: <n> 

Test Command: 

+CMUT=? 

List the supported mute settings. The response is in the form: 

+CMUT: (supported <n>s) 

A.8.68  +CRC – Cellular Result Codes 

ExecSet Command: 

+CRC=[<mode>] 

Set the extended format of incoming data (or voice for A3LA-R/RM/RGS) call indication. 
<mode> takes the following values: 

0  

Disable extended format (default) 

1  

Enable extended format 

If extended format is enabled, the unsolicited result code +CRING: <type> is returned by the 
A3LA-RS instead of RING, where <type> can be one of the following: 

ASYNC   

asynchronous transparent 

SYNC    

synchronous transparent 

REL ASYNC  

asynchronous non-transparent 

REL SYNC  

synchronous non-transparent 

FAX  

 

facsimile 

VOICE    

normal voice 

Read Command: 

+CRC? 

Query the current result code settings. The response is in the form: 

+CR: <mode> 

Test Command: 

+CRC=? 

List the supported result code settings. The response is in the form: 

+CR: (supported <mode>s) 

A.8.69  +CVHU – Voice Hangup Control (Not Applicable to A3LA-RS) 

Set Command: 

+CVHU=[<mode>] 

Selects whether the Hn (hangup) or &Dn command shall cause a voice call connection to be 
disconnected or not. <mode> can take one of the following values: 

0  

Ignore &Dn command specified reaction to DTR ON to OFF transitions. Disconnect 
as reaction to Hn command. OK response given. 

1  

Ignore &Dn command specified reaction to DTR ON to  OFF transitions. Ignore Hn 
command. OK response given. 

Summary of Contents for A3LA-RS






































































































Reviews:

No comments