manualshive.com logo in svg

NAL A3LA-RS, General Description Manual, Page: 41 / 101

Share
Download
NAL A3LA-RS General Description Manual Download Page 41

NAL Research Corporation (TN2012-02-V1.0) 

41 

A.8.64  S0=n – Auto-Answer 

Auto-answer.  This  causes  the  A3LA-RS  to  auto-answer  the  incoming  data  (or  voice  call  for 
A3LA-R/RM/RGS). 

0

 

Disable auto-answer. 

n>0  

Enable auto-answer after n rings 

A.8.65  Xn – Extended Result Codes 

Select the response set to be used by the A3LA-RS when informing the DTE of the results of a 
command or data (or voice call for A3LA-R/RM/RGS). 

0  

OK, CONNECT, RING, NO CARRIER, NO ANSWER and ERROR 
CONNECT response is used to inform of a data call connection; OK response is used 
to inform of a voice call connection (only for A3LA-R/RM/RGS). 

1  

As X0 plus CONNECT x, where x is the DTE speed 

CONNECT x response is used for data calls only. 

2  

As X1 plus NO DIALTONE 

3  

As X2 plus BUSY 

4  

As X3 plus CARRIER x, PROTOCOL: and COMPRESSION:, where x is the line speed 
(default) 
CARRIER  x,  PROTOCOL:,  and  COMPRESSION:  responses  are  used  for  data  calls 
only. 

Note that the Wn command limits which connection related responses will be reported. 

A.8.66  +CLVL – Volume Level Control (Not Applicable to A3LA-RS) 

Exec Command: 

+CLVL=<level> 

This  command  is  used  to  select  the  ‘volume’  of  the  audio  on  the  audio  path.  <level>  is  an 
integer type value with the smallest value representing the lowest sound level. 

Read Command: 

+CLVL? 

Query the current volume level settings. The response is in the form: 

+CLVL: <level> 

0  

Equivalent to level 0 displayed on a handset’s volume indicator 

1  

Equivalent to level 1 displayed on a handset’s volume indicator 

2  

Equivalent to level 2 displayed on a handset’s volume indicator 

3  

Equivalent to level 3 displayed on a handset’s volume indicator 

4  

Equivalent to level 4 displayed on a handset’s volume indicator 

5  

Equivalent to level 5 displayed on a handset’s volume indicator 

6  

Equivalent to level 6 displayed on a handset’s volume indicator 

7  

Equivalent to level 7 displayed on a handset’s volume indicator 

Test Command: 

+CLVL=? 

List the supported volume level settings. The response is in the form: 

+CLVL: (supported <level>s) 

A.8.67  +CMUT – Mute Control (Not Applicable to A3LA-RS) 

Summary of Contents for A3LA-RS






































































































Reviews:

No comments