1 STANDBY LED:
This indicator will light up amber when the M15 HD is
in standby state. When the M15 HD main or zones are in the ON state,
this indicator will illuminate blue. In the unlikely event that the M15
HD switches to protection state, then this indicator will illuminate red.
When infrared command from the HTRM is received, this indicator will
also flash momentarily.
2 STANDBY BUTTON:
Press this button or the HTRM remote’s [ON]
button to switch ON the M15 HD. The Standby LED indicator will turn
from amber to blue and illuminate the VFD. Pressing the standby button
again turns the unit back to standby mode.
The M15 HD can also be switched ON from standby mode by pressing
any of the front panel buttons. When both Main and Zones are ON,
press and hold this button for more than five seconds to place them at
standby mode.
NOTES
· The rear panel POWER switch must be in the ON position for the Standby
button to activate.
· If Auto Trigger IN at Trigger Setup menu is assigned to “Main” or “All”
and the TRIGGER switch is set to “AUTO” mode, the standby button in
the front panel as well as the corresponding ON/OFF function keys in the
HTRM remote control will be disabled effectively handing this function
to an external controller. Switch TRIGGER to “OFF” to maintain normal
power ON/OFF function procedures. See section also about “Trigger
Setup” under the “Setup Menu” discussions.
3 REMOTE SENSOR:
Point the HTRM remote control at the remote
sensor and press the buttons. Do not expose the remote sensor of the
M15 HD to a strong light source such as direct sunlight or illumination.
If you do so, you may not be able to operate the M15 HD with the
remote control.
Distance:
About 23ft (7m) from the front of the remote sensor.
Angle:
About 30° in each direction of the front of the remote sensor.
4 VACUUM FLUORESCENT DISPLAY (VFD):
Displays visual information
about the current settings like the active Source, volume level, listening
mode, audio format, iPod-related display information and other related
indicators. Refer also to the item about DISPLAY SETUP under the USING
THE M15 HD – SETUP MENU segment of the OPERATION section.
5 VOLUME:
Use this control to adjust the overall loudness of the signal
output at AUDIO PRE-OUT. The default volume level is -20dB. The
VOLUME knob is also used to increment/decrement other adjustable
parameters like Tone Controls.
6 SOURCE [
] :
Press these buttons to toggle through the input
selections – Source 1 - 9. Refer also to the item about SOURCE
SETUP under the USING THE M15 HD – SETUP MENU segment of the
OPERATION section.
7 INFO:
Repeatedly toggle this button to display both at the Vacuum
Fluorescent Display (VFD) and On-Screen Display (OSD) the following
– Current Source, Volume level, Listening mode, Audio Source Format,
Audio Codec, Video Mode and active Zones with their corresponding
Source Inputs.
8 LISTENING MODE:
Toggle to select through the various Listening
mode options. Depending on the format of the currently selected input
(digital or analog, stereo or multichannel), various listening modes are
available. Refer also to the item about LISTENING MODE under the
USING THE M15 HD – MAIN MENU segment of the OPERATION section.
9 DIMMER:
Toggle to either reduce or restore normal VFD brightness.
10 TONE CONTROLS:
Press to adjust TREBLE control using the VOLUME
knob over a ± 10dB range. Press again to adjust BASS control and a third
time for DIALOG control. See also section about “Tone Controls” under
“Main Menu” discussions.
11 TONE DEFEAT:
Tone Controls are enabled or disabled by pressing
this button. Tone controls are bypassed at “Tone Defeat” while at “Tone
Active,” the tone controls are enabled again. See also section about
“Tone Controls” under “Main Menu” discussions.
IDENTIFICATION OF CONTROLS
FRONT PANEL
3
4
5
6
11
10
1
2
9
8
7
7
EN
G
LI
SH
FR
ANÇ
AIS
ESP
AÑOL
IT
ALIANO
DEUT
SCH
NEDERL
ANDS
SVENSK
A
РУ
ССКИЙ
