NA-DE V-BUS7, Installation Manual

Page: 100 / 132

29
Screen: Monitor, black/white CRT or colourful LCD
Handset: Allows audio output and input with speaker and microphone
Door Open Button : It is used to open entrance door.
Stairs Automat : It is used to ligth up stairs.
Panel Display : When it is pressed to panel display button, monitor gives the view of camera on the panel for 30 seconds.
If there is more than one panel on the system, if it is pressed to button again during monitor have view of first panel, the
monitor gives the view of second panel. When you press again if there is a third camera, the view of the third camera comes
to the screen, ›f not, display turns off.
CCTV Display : If there is a CCTV camera on the system, it gives the view of CCTV camera on the monitor for 30 seconds.
If there is two CCTV camera on the system, before time is over when it is pressed again displays the other CCTV camera’s
view. If not, display turns off.
Security : It is used to call security. When the handset is hooked and button is pressed, security phone is called. When
the security accept the call, communication starts. If either side does not end the phone call, after 60seconds system
automatically ends the call. If there is more than one security on the system, in order to call first security press button, to
call second security press the switch of the handset once and press button. If the same process is repeated, other securities
are called.
Doorkeeper : It is used to call doorkeeper in NVM series. It is not functional in ND series. When the handset is hooked then
button is pressed, doorkeeper phone is called. When the doorkeeper accept the call, communication starts. If the either
side does not end the phone call, after 60 seconds system automatically ends the call. If there is more than one doorkeeper
in the system, in order to call first doorkeeper press the button, to call second doorkeeper press the switch of the handset
once and press the button. If the same process is repeated , other securities/doorkeepers are called
Ring volume tuning: Allows you to adjust ring volume tone.
Colour / Contrast tuning: Allows you to adjust colour for LCD monitors and contrast for black / white CRT monitors.
Brightness tuning: Allows you to adjust brightness.
External Video Camera Input: This input used for video connection from indoor panel to monitor screen shown in FIGURE-
5.6-D. Camera can be displayed either pressing to door panel or CCTV buton on monitor shown in FIGURE-5.4 In case of
using external video input , 2nd group DIP switch must be set by 4th digit UP position (”1”) as shown in figure 5.3.
Otherwise, if there is no external video input this switch must be DOWN position (”0”). Please refer table-5.3 for 2nd
group of DIP switches for external video input.
75ohm Video Terminating Resistor: This switch should be ON position shown in DIAGRAM-5.6-E
Note: If a detector , which has alarm output , is used in the system , any alarm detection will set the monitors to sound
1- minute long alarm siren.
NVM-550MB/MC ND-107K-8 - ND-108K-8 MONITOR
FIGURE - 5.5
Ring Volume
Tuning
Brigthness Tuning
Colour/Cantrast
Tuning
FIGURE - 5.6
A - System connection terminal
B - Doorbel connection terminal
C - 3rd and 4th audio line
D - External Video Input.
E - 75ohm Video Terminating switch
F- 1st ID switch ( master ID )
G- 2nd ID switch (slave ID )
MONITOR FUNCTIONS
Button LED meanings:
One blink after button is pressed: Button function is implemented
Continuous blinking for door opener LED: Monitor ID settings not completed yet.
Continuous blinking for Security/doorkeeper LEDs: CENTRAL UNIT is in SETUP MODE.
Blinking all LEDs with 3sec periods: Program instruction is confirmed which is typed by keypad.
Blinking all LEDs with 3sec periods as a warning: Program instruction does not confirmed which is typed by keypad.
Apartment calls by keypad:
Press “CALL” button with using one of calling functions from Table-5.4
Example: calling flat no:3 in same block can be made by: pressing 3 “CALL“ keys.
Flat Number
Number
Block No # Flat No
FUNCTIONS
KEYPAD CODE
Calling a flat in same block
Calling a number out of block
Calling a flat out of the block
TABLE-5.4: NVM-550MB/MC KEYPAD CALLING INSTRUCTIONS
DC24V ± 1 (from central unit)
0.4W (Min.), 14W (Max)
8 wires
Full-Dublex
2 doorbell melodies, 2 Phone melodies and 1 Alarm melody
ABS
4” S/B CRT - 4.3” Renkli LCD
Waiting Time : 30 sec, Talking Time : 60 sec
220 (Length) x 200 (Width) x 55 (Heigth) mm
Audio - Brigthness - Colour / Contrast
-20°C - +40°C
IP20
TECHNICAL CHARACTERISTICS
Operation voltage
Power consumption
Connection
Audio communication
Calling Melody
Material Content
Monitor
Monitor operating time
Dimensions
Settings
Operating temperature
Protection class
Functions Calling between Outdoor panel and monitor .
Outdoor panel monitoring.
CCTV monitoring.
Calling security phone and doorkeeper.
Door opener function.
Stairs automat function.
Intercom function.
II
II
III
III
II
II
I
1 2 3
4 5 6
7 8 9
* 0 #
FIGURE - 5.4
Handset
Keypad
Door Open Button
Stairs Automation
Panel Display
CCTV Display
Security
Doorkeeper
Call CANCEL
ID settings can be done only when CENTRAL UNIT is SETUP MODE and function LED is Green.
All monitors must have a unique ID for 1st ID group (main ID ) and it must be different from “0”.
ON OFF
24V
GND
V1
V2
A1
A2
D1
D2
BELL
GND
E
A
B
F
G
C
D