background image

 

 

 

Caution

: An incorrect installation of the system in the helmet may alter the aerodynamic and safety characteristics of 

the helmet itself, thus creating dangerous  conditions. Install the N-Com system according to the instructions 
provided in the product documentation. In case of doubt, please contact your local N-Com dealer. 

 

Warning:

 Listening to other equipment should not interfere with driving the vehicle, which must be the top priority 

at all times. Carry out all operations on the  electronic equipment and on the  N-Com system with the vehicle 
stopped, in compliance with Traffic Regulations.   

 

Caution

: The N-Com system allows reception of the FM radio signal. Any radio licence fees are to the user’s charge. 

 

1.5.

 

Qualified personnel 

Only qualified personnel can carry out technical assistance on this product. In case of any malfunction, always turn to 

your local dealer. 

The helmet is a safety device. Tampering with it and/or with the electronic system inside the  helmet, in addition to 

invalidating the product warranty, can also lead to dangerous situations. 

 

1.6.

 

Accessories and batteries 

 

Only use the type of batteries, battery chargers and accessories approved by Nolan for the specific model. 

 

The  use  of  a  battery  type  different  from  the  recommended  one  may  lead  to  dangerous  situations  and 
invalidate the warranty. 

 

Contact your local dealer to see about the availability of approved accessories. 

 

When disconnecting the power supply  cable of any accessory or of the battery charger, always  grab and  pull 
the plug not the cable. 

 

Do not use batteries for purposes other than the prescribed ones. 

 

Never use batteries or battery chargers that turn out to be damaged. 

 

Do not short-circuit the battery. 

 

Keep the battery at a temperature between 0° / +32°C (charging); -20° / +55°C (in use). 

 

Danger of fire or explosion: do not throw the batteries into a fire nor expose them to high temperatures! 

 

Do not throw out batteries together with household refuse. The batteries should be disposed of in compliance 
with local regulations 

 

Do not wear the helmet while the battery is recharging. 

 

The helmet should never be left within the reach of unsupervised children in order to prevent damage to their 
health caused by access to the batteries. 

 

Battery 

PL053448 

3,7V – 1000 mAh 

Battery charger 

S-TR-009L 

100/240V – 50/60 Hz 5V - 0.5 A 

 

1.7.

 

Disposal 

Refer to this user  manual and to manuals related to  other parts of the N-Com system in order to disassemble the 
system  from  the  helmet.  Once  the  system  has  been  disassembled,  dispose  of  it  according  to  the  following 
instructions: 

 

 

The presence of a crossed-out wheelie bin  indicates that in the European Union the product is 
subject to separate collection at the end of its useful life. 

 

Do not dispose of these products together with undifferentiated urban waste.  

 

The  proper  disposal  of  obsolete  equipment  contributes  to  preventing  possible  negative  consequences  on 
people’s health and on the environment. 

 

For  more  detailed  information  on  the  disposal  of  obsolete  equipment,  contact  your  municipality,  a  waste 
disposal service or the store where the product was purchased. 

Summary of Contents for B901

































Reviews: