manualshive.com logo in svg

Mychef EVOLUTION L 10GN 1/1, Product Manual, Page: 62 / 75

Share
Download
Mychef EVOLUTION L 10GN 1/1 Product Manual Download Page 62

 

 

210208_A 

mychefcooking.com 

62 

PRODUCT MANUAL     SERIE L EVOLUTION     -     DT.MP.LE.2103.2 

17 

ERROR PROBE5 TEMP SENSOR 
NOT CONNECTED 

Reserved. Not used. 

18 

ERROR PROBE5 TEMP SENSOR 
SHORTED 

Reserved. Not used. 

19 

ERROR PROBE6 TEMP SENSOR 
NOT CONNECTED 

Reserved. Not used. 

20 

ERROR PROBE6 TEMP SENSOR 
SHORTED 

Reserved. Not used. 

21 

ERROR PROBE7 TEMP SENSOR 
NOT CONNECTED 

Reserved. Not used. 

22 

ERROR PROBE7 TEMP SENSOR 
SHORTED 

Reserved. Not used. 

23 

ERROR PROBE8 TEMP SENSOR 
NOT CONNECTED 

Chamber probe not connected. Check probe and 
wiring. 

24 

ERROR PROBE8 TEMP SENSOR 
SHORTED 

Short  circuit  chamber  probe.  Check  probe  and 
wiring. 

25 

ERROR PROGRAM NOT 
TERMINATED 

Reserved. Not used. 

26 

ERROR CLEANING PROGRAM 
NOT TERMINATED 

The  oven  has  been  switched  off  by  executing  a 
self-cleaning  program.  Perform  a  rinsing 
program. 

27 

ERROR CLEANING 
TEMPERATURE TOO HOT 

Oven  temperature  during  a  self-cleaning 
program  has  risen  above  a  maximum 
temperature. 

28 

ALARM RECOVERY TEMP TOO 
LOW 

The  oven  has  recovered  from  a  power  outage, 
and  the  temperature  in  the  chamber  was  below 
56ºC. Risk of bacterial contamination. Dispose of 
or test product in the cooking chamber. 

29.1794 

ERROR INVERTER 

Inverter is not getting the correct voltage. Check 
the voltage supply to the inverter and to the oven.  

29.1538 

ERROR INVERTER 

Motor  consumption  too  high.  Ensure  the  motor 
works softly and the bearings are not damaged. 

29.5890 

ERROR INVERTER 

Ambient temperature in inverter too high. Ensure 
the oven is cooling correctly. 

Table 8. Errors, alarms, and possible solutions 

 

 

Always run a self-cleaning or rinsing program when Error 26 occurs. 

 Check whether errors can be removed by your own means, or if not, contact your service 
representative.  

Summary of Contents for EVOLUTION L 10GN 1/1












































































Reviews:

No comments