manualshive.com logo in svg

MW 829700102, Man, Page: 40 / 44

Share
Download
MW 829700102 Man Download Page 40

40

M1.1.TPT1300-TPT2000.NLFREN   08122017

EN

7.  Carefully fold the upper handle down. Do not allow control cables to 

become pinched or bent. 

8.  Store your plate compactor in upright position in a clean, dry building 

that has good ventilation.

Do not store compactor with fuel in a non-ventilated 

area where fuel fumes may reach flame, sparks, pilot 

lights or any ignition sources.

Use only approved fuel containers.

9  Troubleshooting

Problem

Cause

Remedy

Engine fails to start

Spark plug wire disconnected.

Attach spark plug wire securely to spark 

plug.

Out of fuel or stale fuel.

Fill with clean, fresh gasoline.

Throttle control lever not in correct 

starting position.

Move throttle control lever to start 

position.

Choke not in ON Position.

Throttle must be positioned at choke for 

a cold start.

Blocked fuel line.

Clean the fuel line.

Fouled spark plug.

Clean, adjust gap, or replace.

Engine flooding.

Wait a few minutes to restart, but do not 

prime.

Engine runs erratically

Spark plug wire loose.

Connect and tighten spark plug wire.

Unit running on CHOKE.

Move choke lever to OFF.

Blocked fuel line or stale fuel.

Clean fuel line. Fill tank with clean, fresh 

gasoline.

Vent plugged.

Clear vent.

Water or dirt in fuel system.

Drain fuel tank. Refill with fresh fuel.

Dirty air cleaner.

Clean or replace air cleaner.

Engine overheats

Engine oil level low.

Fill crankcase with proper oil.

Dirty air cleaner.

Clean air cleaner.

Air flow restricted.

Remove housing and clean.

Engine will not stop when throttle control 

is positioned at stop, or engine speed 

does not increase properly when throttle 

control is adjusted.

Debris interfering with throttle linkage.

Clean dirt and debris.

Compactor is difficult to control when 

pounding (machine jumps or lurches 

forward)

Too high engine speed on hard ground. Set the throttle lever at lower speed.

PLATE COMPACTOR

16

GB

TRANSPORTING

See technical data for the weight of the 
machine.

To avoid burns or fire hazards, let engine 
cool before transporting machine or storing 
indoors.

The unit must be transported in the upright 
position to prevent fuel from spilling. Do not 
lay machine on its side or top.

Secure or tie down unit using the lifting handle 
to prevent machine from sliding or tipping 
over.

Pull up the spring bolt and fold up the 
wheels bracket.

Carefully fold the upper handle down. 
Do not allow control cables to become 
pinched or bent.

Store your plate compactor in upright 
position in a clean, dry building that has 
good ventilation.

5.

6.

7.

Machine may fall and cause damage 
or injury if lifted incorrectly. Lift 
using handles at base of plate.

Do not use strong detergents or 
petroleum based cleaners when 
cleaning plastic parts. Chemicals 
can damage plastics.

29242UK00M101-改.indd   16

2016/6/23   17:58:40

copyrighted 

document 

- all 

rights 

reserved 

by 

FBC

Summary of Contents for 829700102













































Reviews:

No comments