manualshive.com logo in svg

MW 829700102, Man, Page: 34 / 44

Share
Download
MW 829700102 Man Download Page 34

34

M1.1.TPT1300-TPT2000.NLFREN   08122017

EN

Paving pad kit (optional)

The transparent rubber paving pad allows to compact 

concrete slabs, stones, bricks and blocks silently and gently. 

Attach the paving pad onto the base plate as shown. Align 

the holes in the base plate, paving pad and clamp plate, and 

secure it with 3 bolts M10x25 and lock washers.

Engine oil

Add oil.

WARNING!

Oil has been drained for shipping.

Failure to fill engine sump with oil before 

starting engine will result in permanent 

damage and will void engine warranty.

5  Lifting and transporting

See technical data for the weight of the machine.

To avoid burns or fire hazards, let engine cool before lifting/transporting machine or storing indoors.

The unit can be lifted by the handles in front and back of the unit as shown.

The unit must be transported in the upright position to prevent fuel from spilling. Do not lay machine on its side or top.

Secure or tie down unit using the lifting handle to prevent machine from sliding or tipping over.

WARNING!

Machine may fall and cause damage or injury if lifted incorrectly. Lift using handles at base of 

plate.

6  Operation

Adding fuel

Fill the fuel tank.

Starting engine

1.  Move the fuel valve lever to the ON position

2.  To start a cold engine, move the choke to the CLOSE position. 

To restart a warm engine, leave the choke lever in the OPEN position.

3.  Move the throttle lever away from the SLOW position, about 1/3 of the way toward the FAST position.

4.  Turn the engine switch to the ON position. 

5.  Operate the starter.

2.  Pull up the spring bolt and put the upper pipe of the 

wheels bracket into the mounting bracket. Align both ends 

of the pipe with the holes. Slide the bolt in and secure 

with the clips.

PLATE COMPACTOR

8

GB

Add oil according to 

Engine Manual

 packed 

separately with your tiller.

Engine Oil

O I L   H A S   B E E N   D R A I N E D   F O R 
SHIPPING.

Failure to fill engine sump with oil 
before starting engine will result in 
permanent damage and void engine 
warranty.

Attach the Paving Pad onto the Base Plate 
as shown. Align the holes in the Base Plate, 
Paving Pad and Clamp Plates, and secure it 
with 3 bolts M10x25 and lock washers. (Only 2 
bolts and lock washers for #29240.)

Paving Pad Kit (Optional)

The transparent rubber Paving Pad allows to 
compact concrete paving slabs, stones, bricks 
and blocks silently and gently. 

  

M10 X 25

X 3

D

Pull up the spring bolt and put the upper 
pipe of the wheels bracket into the 
mounting bracket. Align two ends of the 
pipe with the holes. Slide the bolt in and 
secure with the clips.

2.

29242UK00M101-改.indd   8

2016/6/23   17:58:36

copyrighted 

document 

- all 

rights 

reserved 

by 

FBC

Summary of Contents for 829700102













































Reviews:

No comments