manualshive.com logo in svg

Munters TRIO, User And Installation Manual

Share
Download
Munters TRIO User And Installation Manual Download Page 50

 

 

© Munters AB, 2020 

50

 

7

 

Mapping and Defining the Input Output 

Devices 

NOTE

 

Munters recommends that a trained technician perform the following operations. 

•

 

Mapping Devices 

•

 

Temperature Sensors 

•

 

Ventilation Devices 

•

 

Sensors 

•

 

Heating Devices 

•

 

Defining the Cooling Devices 

•

 

Inlets, Tunnel Doors, Outlets 

•

 

Defining the Same As Relays 

•

 

Defining the Same As Analog Ports 

•

 

Defining the Timer 

•

 

Defining the Auxiliary Input 

•

 

Lighting Devices 

•

 

Feeding Devices 

•

 

Defining the Silos 

•

 

Defining the Bird Scales 

•

 

Defining the TRIO RPS 

7.1

 

Mapping Devices 

After wiring devices to the TRIO, each device must be mapped and then defined. Mapping and defining 
devices enables the system software to control each device’s functionality.  
CAUTION

 

Mapping MUST match the physical wiring! An error message appears if the physical device 

is not wired to the relay or port as defined on the mapping screen..  

Summary of Contents for TRIO















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands