Munters TRIO User And Installation Manual Download Page 5

Page: 5 / 206

7.4.2

Defining the CO2 Sensor

.......................................................................................................

7.4.3

Defining the Humidity Sensor

...............................................................................................

7.4.4

Defining the Water Meter Sensor

.......................................................................................

7.5

Heating Devices

---------------------------------------------------------------------------------------------------------------------------------------------------------------

7.5.1

Defining the On/Off Heaters

...............................................................................................

7.5.2

Defining the Variable Heaters

..............................................................................................

7.6

Defining the Cooling Devices

-----------------------------------------------------------------------------------------------------------------------------------

7.7

Inlets, Tunnel Doors, Outlets

--------------------------------------------------------------------------------------------------------------------------------------

7.7.1

Defining the Inlets/Tunnel Doors

.........................................................................................

7.7.2

Defining the Outlet

...................................................................................................................

7.8

Defining the Same As Relays

------------------------------------------------------------------------------------------------------------------------------------

7.9

Defining the Same As Analog Ports

----------------------------------------------------------------------------------------------------------------------

7.10

Defining the Timer

------------------------------------------------------------------------------------------------------------------------------------------------------------

7.11

Defining the Auxiliary Input

---------------------------------------------------------------------------------------------------------------------------------------

7.12

Lighting Devices

----------------------------------------------------------------------------------------------------------------------------------------------------------------

7.12.1

Defining the On/Off Lights

....................................................................................................

7.12.2

Defining the Variable Lights

..................................................................................................

7.12.3

Defining the Light Sensor

........................................................................................................

7.13

Feeding Devices

---------------------------------------------------------------------------------------------------------------------------------------------------------------

7.13.1

Defining the Auger Relays

.....................................................................................................

7.13.2

Defining the Auger Active Sensors

.....................................................................................

7.13.3

Defining the Feeder Relays

....................................................................................................

7.13.4

Defining the Feeder Active Sensors

....................................................................................

7.14

Defining the Silos

-------------------------------------------------------------------------------------------------------------------------------------------------------------

7.14.1

Mapping the Silo Scales

........................................................................................................

7.14.2

Configuring the Silo Scale

.....................................................................................................

7.15

Defining the Bird Scales

-----------------------------------------------------------------------------------------------------------------------------------------------

7.15.1

Mapping the Bird Scales

.......................................................................................................

7.15.2

Calibrating the Bird Scales

....................................................................................................

7.15.3

Testing the Bird Scale

..............................................................................................................

7.16

Defining the TRIO RPS

---------------------------------------------------------------------------------------------------------------------------------------------------

7.16.1

Define the Sensor

......................................................................................................................

7.16.2

Static Pressure Calibration

.....................................................................................................

FLOCK MANAGEMENT -------------------------------------------------------------------------------------------------------------------------- 95

8.1

Defining the General Settings

----------------------------------------------------------------------------------------------------------------------------------

8.1.1

Defining the Preferences

.........................................................................................................

8.1.2

Defining the Time/Date

..........................................................................................................

8.1.3

Defining the House Setting

....................................................................................................

8.2

Flock Settings

----------------------------------------------------------------------------------------------------------------------------------------------------------------------

8.2.1

Defining the Flock Settings Parameters

.............................................................................

Summary of Contents for TRIO















































































































































































































Search results

Summary of Contents for TRIO

Reviews:

Brands by name

Popular brands

Munters TRIO, User And Installation Manual

Search results

Summary of Contents for TRIO

Reviews:

Brands by name

Popular brands