manualshive.com logo in svg

Munters TRIO, User And Installation Manual

Share
Download
Munters TRIO User And Installation Manual Download Page 11

 

 

© Munters AB, 2020 

11

 

2

 

Precautions 

CAUTION

 

Protection provided by the equipment can be impaired if the equipment is used in a manner 

not specified by the manufacturer! 

CAUTION

 

There is a risk of explosion if the lithium battery is replaced with an incorrect type. Replace 

the battery using the same type and manufacturer only. 

•

 

Grounding 

•

 

Filtering 

•

 

Checking the Battery Level 

•

 

Frequency Inverters 

2.1

 

Grounding 

•

 

Always connect temperature and sensor shields to earth ground.

 

Avoid mixing high voltage 

wiring with sensor and low voltage wiring

.

 

•

 

Keep the controller as far as possible from heavy contactor boxes and other sources of 
electrical interference

.

 

•

 

Do not connect communication wire shields, which go from one house to another at both ends.  
Connect them at one end only.  Connection at both ends can cause ground loop currents to 
flow, which reduce reliability

.

 

•

 

The COM connection for communications is not the shield wire.  The COM, RX and TX wires 
must connect to each other at all controllers

.

 

2.2

 

Filtering

 

 

If this installation includes a power inverter to drive variable speed fans, install an EMI filter in front of the 
inverter, according to the specifications provided by the inverter manufacturer. Refer to the inverter 
documentation. 

2.3

 

Checking the Battery Level 

Check the battery once a year. The output must be 2.7 volts (minimum). Authorized personnel only must 
replace the battery if the output is below the minimum required level or every five years. 

2.4

 

Frequency Inverters 

Frequency inverters can cause severe electrical and electromagnetic interference. Therefore, when 
employing a frequency inverter, it is critical that you carefully follow the manufacturer's installation 
instructions.   
In particular verify: 

•

 

That the cable shielding between the inverter and any motor meets industry standards 

•

 

Proper grounding of the inverter's chassis and motor power cable 

Summary of Contents for TRIO















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands