MULTIQUIP CD6CE13H18 Operation Manual Download | Manualshive

Page: 5 / 34

background image

STOW CUTTER 1 CE — OPERATION MANUAL — REV. #2 (12/20/07) — PAGE 5

STOW CUTTER 1 CE SAW — SAFETY MESSAGE ALERT SYMBOLS

Safety precautions should be followed at all times when operating
this equipment. Failure to read, understand and comply with the
Safety Messages and Operating Instructions could result in injury
to yourself or others.

FOR YOUR SAFETY AND THE SAFETY OF OTHERS!

This Owner's Manual has been developed to provide
instructions for the safe and efficient operation of the
STOW CUTTER 1 CE SAW. For engine maintenance
information, please refer to the engine manufacturers'
instructions for data relative to its safe operation.

Before using this CONCRETE/ASPHALT SAW,
ensure that the operating individual has read and
understands all instructions in this manual.

NOTE

SAFETY MESSAGE ALERT SYMBOLS

The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure to
the operator, and are preceded by one of three words:

DANGER

,

WARNING

, or

CAUTION

.

Potential hazards associated with CUTTER 1 CE operation will
be referenced with "

Hazard Symbols

" which appear throughout

this manual, and will be referenced in conjunction with Safety
"

Message Alert Symbols

".

HAZARD SYMBOLS

Burn Hazards

Engine components can generate extreme heat.
To prevent burns,

DO NOT

touch these areas

while the engine is running or immediately after
operations.

NEVER

operate the engine with

heat shields or heat guards removed.

Rotating Parts

NEVER

operate equipment with covers, or

guards removed. Keep fingers,

hands

,

hair

and

clothing

away from all moving parts to

prevent injury.

Guards and Covers In Place

NEVER

operate the saw without blade guards

and covers in place. Adhere to safety
guidelines and applicable local regulations.

Engine exhaust gases contain poisonous
carbon monoxide. This gas is colorless and
odorless, and can cause death if inhaled.

NEVER

operate this equipment in a confined

area or enclosed structure that does not
provide ample free flow air.

Lethal Exhaust Gases

You

WILL

be

KILLED

or

SERIOUSLY INJURED

if you

DO NOT

follow these directions.

You

CAN

be

KILLED

or

SERIOUSLY INJURED

if

you

DO NOT

follow these directions.

You

CAN

be

INJURED

if you

DO NOT

follow

these directions.

CAUTI

CAUTI

CAUTI

CAUTI

CAUTION

DANGER

DANGER

DANGER

DANGER

DANGER

WARNING

WARNING

WARNING

WARNING

WARNING

«
...
3
4
5
6
7
...
»

Summary of Contents for CD6CE13H18



































Reviews:

No comments

Related manuals for CD6CE13H18

Brand: Jet Pages: 28

Brand: nativa Pages: 36

Brand: Kalamazoo Pages: 6

Brand: Force Pages: 25

Brand: Powerplus Pages: 12

Brand: Parkside Pages: 100

Brand: Chicago Electric Pages: 36

Brand: Milwaukee Pages: 12

Brand: Black & Decker Pages: 34

Fire Storm 609746-08

Brand: Black & Decker Pages: 7

Brand: Black & Decker Pages: 7

FireStorm FS18SS

Brand: Black & Decker Pages: 40

Brand: Black & Decker Pages: 7

Brand: Black & Decker Pages: 84

Brand: Black & Decker Pages: 96

Brand: Black & Decker Pages: 96

Brand: Black & Decker Pages: 4

Brand: Black & Decker Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands