background image

PAGE 8 — STOW CUTTER 1 CE — OPERATION MANUAL — REV. #2 (12/20/07)

STOW CUTTER 1 CE SAW — RULES FOR SAFE OPERATION

Examine blade flanges for damage and excessive wear.

Ensure the cleanliness of the blade before blade is installed.
Blade should fit snugly on the shaft and against the inside/
outside blade flanges.

Ensure the blade is marked with an operating speed greater
than the spindle speed of the saw.

Only cut the material that is specified for the diamond blade.
Read the specifications of the diamond blade to ensure the
proper tool has been matched to the material being cut. The
saw has been engineered for 

WET CUTTING

.  Ensure a

WET CUTTING

 blade is being used and that the water supply

system to the blade is properly functioning and being used.

ALWAYS

 keep blade guards in place.  Exposure of the

diamond blade must not exceed 180 degrees.

Ensure that the diamond blade does not come into contact
with the ground or surface during transportation.  

DO NOT

drop the diamond blade on ground or surface.

The  engine governor is set to permit maximum engine speed
in a no-load condition.  Do not tamper with the engine
governor to increase the speed.  Increasing the engine speed
could allow the maximum rated spindle speed to be
exceeded, creating an unsafe condition.

Ensure that the blade is mounted for proper operating
direction. (See Figure 3, page 15)

Adhere to the Blade Manufacturer's recommendations on
handling, storage, and safe usage of blades.

General Safety

ALWAYS 

 read, understand, and follow procedures in

Operator's Manual before attempting to operate equipment.

ALWAYS  

be sure the operator is familiar with proper safety

precautions and operating techniques before using the saw.

NEVER

 leave the machine 

unattended

 while running.

Apply the brakes when leaving or when using on a slope.

Maintain this equipment in a safe operating condition at all
times.

ALWAYS 

 stop the engine before servicing, adding fuel and

oil.

NEVER 

run the engine without the air filter.  Severe engine

damage could occur.

ALWAYS 

 service air cleaner frequently to prevent carburetor

malfunction.

AVOID

 wearing jewelry or loose fitting clothing that may snag

on the controls or moving parts, this can cause a serious
injury.

ALWAYS 

 keep clear of 

rotating

 or 

moving parts

 while the

saw is in operation.

WARNING

ALWAYS 

 check to make sure that the

cutting area is clear before starting the
engine.

Keep all inexperienced and unauthorized people clear of
the cutting area when operating the saw.

Always observe all applicable compulsory regulations
relevant to environmental protection, especially fuel storage,
the handling of hazardous substances, and the wearing of
protective clothing and equipment.  Instruct the user as
necessary, or, as the user, request this information and
training.

WARNING

ALWAYS 

 store equipment properly when it is not being used.

Equipment should be stored in a clean, dry location out of
the reach of children.

Diamond Blade Safety

Use appropriate steel centered diamond blades
manufactured for use on concrete saws.  See further blade
information on pages 19 to 21.

ALWAYS 

 keep the work area well organized.

ALWAYS 

 Clear the cutting area of any debris, tools, etc. that

would constitute a hazard while the saw is in operation.

ALWAYS

 inspect diamond blades

before each use.  The blade should
exhibit  no cracks, dings, or flaws in
the steel centered core and/or rim.
Center (arbor) hole must be
undamaged and true.

Summary of Contents for CD6CE13H18



































Reviews: