MULTILIFT ULTIMA S Installation Instructions Manual Download Page 57

Page: 57 / 62

Installation

Ultima Hooklift

01/2020

6.7 Connectivity gateway antenna

The gateway antenna is delivered loose in the packing box and the antenna bracket is installed

in front of the left side subframe beam. Exception is the hooklift with tool console where the

antenna is preinstalled in the factory.

The best place for the antenna is on top and at back of the truck cabin.

The gateway module is installed on the control valve bracket.

The illustration below is showing the location of the antenna bracket in new hooklift delivery.

The correct and suitable location must be checked during the installation, before the connectiv-

ity gateway is taken into use.

THE ANTENNA SHOULD BE INSTALLED TO A POSITION WHERE VISIBILITY

TO THE SKY IS AS GOOD AS POSSIBLE!

CV side

CV front

CV tool console

Summary of Contents for ULTIMA S































































Search results

Summary of Contents for ULTIMA S

Reviews:

Related manuals for ULTIMA S

Brands by name

Popular brands

MULTILIFT ULTIMA S, Installation Instructions Manual

Search results

Summary of Contents for ULTIMA S

Reviews:

Related manuals for ULTIMA S

Brands by name

Popular brands