Multi-Tech MultiFRAD 200 Series, User Manual

Page: 79 / 85

79
Glossary
Multiplexer (Mux): 1. A device that takes several input signals and combines them into a single output signal in such a manner that
each of the input signals can be recovered. 2. A device capable of interleaving the events of two or more activities or capable of
distributing the events of an interleaved sequence to the respective activities. 3. Putting multiple signals on a single channel.
Multiprotocol: A device that can interoperate with devices utilizing different network protocols.
Multithreading: The ability of a software system to be able to handle more than one transaction concurrently. This is contrasted to the
case where a single transaction is accepted and completely processed before the next transaction processing is started.
N
Nailed Connection: A permanent or dedicated circuit of a previously switched circuit or circuits.
Nailed-up Circuit: A semipermanent circuit established through a circuit-switching facility for point-to-point connectivity.
NAK (Negative Acknowledgment): Communications code used to indicate that a message was not properly received, or that a
terminal does not wish to transmit. Contrast with ACK.
Network: A group of computers connected by cables or other means and using software that enables them to share equipment, such
as printers and disk drives to exchange information.
Node: Any point within a network which has been assigned an address.
O
Object-Orientated: A method for structuring programs as hierarchically organized classes describing the data and operations of objects
that may interact with other objects.
Office Channel Unit - Data Port (OCU-DP): The CO channel bank used as the interface between the customer's DSU and the
channel bank.
Off-hook: The condition of a device which has accessed a phone line (with or without using the line). In modem use, this is equivalent
to a telephone handset being picked up. Dialing and transmission are allowed, but incoming calls are not answered. Contrast "on-hook".
Off Premise Extension (OPX): An extension or phone that terminates in a location other than that of the PBX. Commonly used to
provide a corporate member with an extension of the PBX at home.
Ones Density: the measure of the number of logical 1s on a T1 line compared to a given total number of bits on that line; used for
timing information in data recovery in AMI and B8ZS.
On-Hook: The condition of a device which has not accessed a phone line. In modem use, this is equivalent to a telephone handset that
has not been picked up. In other words, it can receive an incoming call. Contrast "off-hook".
Open Shortest Path First (OSPF): A hierarchical Interior Gateway Protocol (IGP) routing algorithm for IP that is a proposed standard
for Internet. OSPF incorporates least-cost routing, equal-cost routing, and load balancing.
Outage: The measure of the time during which a circuit is not available for use due to service interrupt. Outage is the complement of
circuit "availability" (100% minus % available = % outage).
Out-of-band: Signaling that is separated from the channel carrying the information (i.e., the voice/data/video signal is separate from the
carrier signal). Dialing and various other "supervisory" signals are included in the signaling element. Contrast "In-band" signaling.
Out of Frame (OOF): A T1 alarm condition that is logged on the loss of 2, 3 or 4 of 5 consecutive FT framing bits.
P
Packet: 1. In data communication, a sequence of binary digits, including data and control signals, that is transmitted and switched as a
composite whole. The data, control signals and, possibly, error control information are arranged in a specific format. 2. Synonymous with
data frame. 3. In TCP/IP, the unit of data passed across the interface between the Internet layer and the link layer. A packet includes an
IP header and data. A packet can be a complete IP datagram or a fragment of an IP diagram. 4. In X.25, a data transmission information
unit. A group of data and control characters, transferred as a unit, determined by the process of transmission. Commonly used data field
lengths in packets are 128 or 256 bytes. 5. The field structure and format defined in the CCITT X.25 recommendation.
Packet Assembler/Dissembler (PAD): Used by devices to communicate over X.25 networks by building or stripping X.25 information
on or from a packet.
Packet Data: The information format ("packetized") used for packet-mode calls.
Packet Mode: Refers to the switching of chunks of information for different users using statistical multiplexing to send them over the
same transmission facility.
Parity bit: An extra bit attached to each byte of synchronous data used to detect errors in transmission.
Permanent Virtual Circuit (PVC): A connection between two endpoints dedicated to a single user. IN ISDN, PVCs are established by
network administration and are held for as long as the user subscribes to the service.