manualshive.com logo in svg

MTU 12 V 4000 Lx4, Operating Instructions Manual, Page: 66 / 199

Share
Download
MTU 12 V 4000 Lx4 Operating Instructions Manual Download Page 66

112609  –  LOLO T-Exhaust A9

Red alarm. Initiated by EMU.

Cause

Corrective action

Individual exhaust gas
temperature of this cylinder is
too low in comparison with
weighted average.

1. Check spark plug.
2. Check emission values.
3. Check ignition timing (→ Page 160).
4. Check valve drive.

112610  –  LOLO T-Exhaust A10

Red alarm. Initiated by EMU.

Cause

Corrective action

Individual exhaust gas
temperature of this cylinder is
too low in comparison with
weighted average.

1. Check spark plug.
2. Check emission values.
3. Check ignition timing.
4. Check valve drive (→ Page 160).

112611  –  LOLO T-Exhaust B1

Red alarm. Initiated by EMU.

Cause

Corrective action

Individual exhaust gas
temperature of this cylinder is
too low in comparison with
weighted average.

1. Check spark plug.
2. Check emission values.
3. Check ignition timing (→ Page 160).
4. Check valve drive.

112612  –  LOLO T-Exhaust B2

Red alarm. Initiated by EMU.

Cause

Corrective action

Individual exhaust gas
temperature of this cylinder is
too low in comparison with
weighted average.

1. Check spark plug.
2. Check emission values.
3. Check ignition timing (→ Page 160).
4. Check valve drive.

112613  –  LOLO T-Exhaust B3

Red alarm. Initiated by EMU.

Cause

Corrective action

Individual exhaust gas
temperature of this cylinder is
too low in comparison with
weighted average.

1. Check spark plug.
2. Check emission values.
3. Check ignition timing (→ Page 160).
4. Check valve drive.

66 | Troubleshooting | MS15027/00E 2013-10

TIM-ID: 0000044566 - 001

Summary of Contents for 12 V 4000 Lx4








































































































































































































Reviews:

No comments