manualshive.com logo in svg

MTU 12 V 4000 Lx4, Operating Instructions Manual, Page: 59 / 199

Share
Download
MTU 12 V 4000 Lx4 Operating Instructions Manual Download Page 59

112414  –  LO T-Exhaust B4

Yellow alarm. Initiated by EMU.

Cause

Corrective action

Individual exhaust gas
temperature of this cylinder is
too high in comparison with
weighted average.

1. Check spark plug.
2. Check emission values.
3. Check ignition timing (→ Page 160).
4. Check valve drive.

112415  –  LO T-Exhaust B5

Yellow alarm. Initiated by EMU.

Cause

Corrective action

Individual exhaust gas
temperature of this cylinder is
too high in comparison with
weighted average.

1. Check spark plug.
2. Check emission values.
3. Check ignition timing (→ Page 160).
4. Check valve drive.

112416  –  LO T-Exhaust B6

Yellow alarm. Initiated by EMU.

Cause

Corrective action

Individual exhaust gas
temperature of this cylinder is
too high in comparison with
weighted average.

1. Check spark plug.
2. Check emission values.
3. Check ignition timing (→ Page 160).
4. Check valve drive.

112417  –  LO T-Exhaust B7

Yellow alarm. Initiated by EMU.

Cause

Corrective action

Individual exhaust gas
temperature of this cylinder is
too high in comparison with
weighted average.

1. Check spark plug.
2. Check emission values.
3. Check ignition timing (→ Page 160).
4. Check valve drive.

112418  –  LO T-Exhaust B8

Yellow alarm. Initiated by EMU.

Cause

Corrective action

Individual exhaust gas
temperature of this cylinder is
too high in comparison with
weighted average.

1. Check spark plug.
2. Check emission values.
3. Check ignition timing (→ Page 160).
4. Check valve drive.

MS15027/00E 2013-10

| Troubleshooting | 59

TIM-ID: 0000044566 - 001

Summary of Contents for 12 V 4000 Lx4








































































































































































































Reviews:

No comments