manualshive.com logo in svg

MTU 12 V 4000 Lx4, Operating Instructions Manual, Page: 122 / 199

Share
Download
MTU 12 V 4000 Lx4 Operating Instructions Manual Download Page 122

231  –  SD Camshaft Speed

Red alarm. Engine stop.
Associated parameter 1.8004.499

Cause

Corrective action

Camshaft sensor defective,
short circuit or wire break.

u

Check sensor and cabling (B1.1), replace if necessary. Fault is
rectified following engine restart.

232  –  SD Charger 1 Speed

Yellow alarm.
Associated parameter 1.3011.128

Cause

Corrective action

Speed sensor of primary
turbocharger defective, short
circuit or wire break.

u

Turbocharger speed sensor is not fitted at present.

233  –  SD Charger 2 Speed

Yellow alarm.
Associated parameter 1.3011.129

Cause

Corrective action

Speed sensor of secondary
turbocharger defective, short
circuit or wire break.

u

Turbocharger speed sensor is not fitted at present.

245  –  SD ECU Power Supply Voltage

Red alarm.
Associated parameter 2.8006.589

Cause

Corrective action

Internal governor fault.

u

Replace ADEC engine governor.

266  –  SD Speed Demand

Red alarm.
Associated parameter 2.8006.586

Cause

Corrective action

Speed setting signal can no
longer be transmitted from
plant.

u

Check signal and cabling between plant and ADEC.

122 | Troubleshooting | MS15027/00E 2013-10

TIM-ID: 0000044567 - 001

Summary of Contents for 12 V 4000 Lx4








































































































































































































Reviews:

No comments