MTS Sensors Temposonics T-Series Operation Manual Download

Page: 38 / 52

Temposonics

TH CANbus ATEX / IECEx / CEC / NEC / KCs / EAC Ex certified / Japanese approval

Operation Manual

COB-ID

Request /

Respond

DLC

Byte

Description

0x67F

0x22

0x10

0x01

0x73

0x61

0x76

0x65

Note:

This takes at least 20 ms of time!

0x5FF

0x60

0x10

0x01

0x00

COB-ID

Request /

Respond

DLC

Byte

0x67F

0x22

0x11

0x10

0x01

0x6C

0x6F

0x61

0x64

0x5FF

0x60

0x11

0x10

0x01

0x00

5.7.6 SDO store parameter index 1010

Using the store parameter command, all current settings are transferred into permanent memory.

Table 13: Store parameter and sensor response

Table 14: Restore parameters

Table 15: Device properties

Index

Sub-index

Description

Type

Attribute

Default Value

Comment

1005

COB-ID sync

Unsigned 32

0x080

1008

Device name

String

C304

1009

Hardware version release

String

1.00

100A

Software version release

String

1.01

100B

Node-ID

Unsigned 32

0x7F

100C

Guard time

Unsigned 16

100D

Life time factor

Unsigned 8

100E

COB-ID Guarding Protocol

Unsigned 32

0x700 + Node-ID

100F

Number of SDOs supported

Unsigned 32

0x01

1014

COB-ID EMCY

Unsigned 32

0x080 + Node-ID

1017

Producer heartbeat

Unsigned 16

1018

Identity object

Unsigned 8

Vendor-ID

Unsigned 32

0x00000040

MTS Sensor

Product code

Unsigned 32

0x43333034

C304

Revision number

Unsigned 32

0x00010005

Serial number

Unsigned 32

17143876

5.7.7 Restore default parameters index 1011

Using the restore parameter command, all current settings are restored to default values.

5.7.8 Sensor communication default parameter

These parameters are related to the C304 order code configuration type.

Summary of Contents for Temposonics T-Series





















































Search results

Summary of Contents for Temposonics T-Series

Reviews:

Related manuals for Temposonics T-Series

Brands by name

Popular brands

MTS Sensors Temposonics T-Series, Operation Manual

Search results

Summary of Contents for Temposonics T-Series

Reviews:

Related manuals for Temposonics T-Series

Brands by name

Popular brands