MTS Sensors Temposonics T-Series Operation Manual Download

Page: 25 / 52

Temposonics

TH CANbus ATEX / IECEx / CEC / NEC / KCs / EAC Ex certified / Japanese approval

Operation Manual

6/ •

Be sure that the float specific gravity is at least 0.05 less than that of the measured

liquid as a safety margin at ambient temperature

•

For interface measurement: A minimum of 0.05 specific gravity differential is

required between the upper and lower liquids

•

When the magnet is not shown, the magnet is positioned at the center line of float

•

An offset weight is installed in the float to bias or tilt the float installed on the sensor

tube. So the float remains in contact with the sensor tube at all times and guarantees

permanent potential equalization of the float. The offset is required for installations

that must conform to hazardous location standards

Floats

Ø 18

(Ø 0.71)

(1.97)

Ø 47

(Ø 1.85)

(2.13)

Ø 18

(Ø 0.71)

(1.22)

(1.06)

Ø 47

(Ø 1.85)

Ø 18

(Ø 0.71)

Ø 47

(Ø 1.85)

(3.03)

Ø 18

(Ø 0.71)

Ø 47

(Ø 1.85)

(3.03)

Float

Part no. 201 605-2

Float

Part no. 201 606-2

Float

Part no. 251 982-2

Float

Part no. 251 983-2

Material: Stainless steel 1.4571

(AISI 316 Ti)

Weight offset: Yes

Pressure: 4 bar (60 psi)

Magnet offset: Yes

Specifi c gravity: Max. 0.6

Operating temperature:

−40…+125 °C (−40…+257 °F)

Material: Stainless steel 1.4571

(AISI 316 Ti)

Weight offset: Yes

Pressure: 4 bar (60 psi)

Magnet offset: Yes

Specifi c gravity: 0.93 ± 0.01

Operating temperature:

−40…+125 °C (−40…+257 °F)

Material: Stainless steel (AISI 316L)

Weight offset: Yes

Pressure: 29.3 bar (425 psi)

Magnet offset: No

Specifi c gravity: 0.93 ± 0.01

Operating temperature:

−40…+125 °C (−40…+257 °F)

Material: Stainless steel (AISI 316L)

Weight offset: Yes

Pressure: 29.3 bar (425 psi)

Magnet offset: No

Specifi c gravity: 1.06 ± 0.01

Operating temperature:

−40…+125 °C (−40…+257 °F)

Standard float that can be expedited Standard float that can be expedited

Float

Collar

Optional installation hardware

Ø 18

(Ø 0.71)

Ø 47

(Ø 1.85)

(3.03)

(0.16)

Ø 27

(Ø 1.06)

Ø 10

(Ø 0.39)

(0.2)

(0.35)

8-32 threads

(0.31)

20 (0.79)

60 (2.36)

16 (0.63)

12 (0.47)

3.2 (0.13)

Ø 3.2 (Ø 0.13)

M3 fastening screws (6×)

Float

Part no. 251 981-2

Stop collar

Part no. 560 777

Fixing clip

Part no. 561 481

Material: Stainless steel (AISI 316L)

Weight offset: Yes

Pressure: 29.3 bar (425 psi)

Magnet offset: No

Specifi c gravity: Max. 0.67

Operating temperature:

−40…+125 °C (−40…+257 °F)

Provides end of stroke stops for ﬂ oat

Material: Stainless steel 1.4301

(AISI 304)

Weight: Approx. 30 g
Hex key

⁄

" required

Application: Used to secure sensor

rods (Ø 10 mm (Ø 0.39 in.)) when

using an U-magnet or block magnet

Material: Brass, non-magnetic

Controlling design dimensions are in millimeters and measurements in ( ) are in inches

Summary of Contents for Temposonics T-Series





















































Search results

Summary of Contents for Temposonics T-Series

Reviews:

Related manuals for Temposonics T-Series

Brands by name

Popular brands

MTS Sensors Temposonics T-Series, Operation Manual

Search results

Summary of Contents for Temposonics T-Series

Reviews:

Related manuals for Temposonics T-Series

Brands by name

Popular brands