background image

mr

.

steam

®

club therapy

®

Installation, Operation & Maintenance Manual

______________________________________________________________________________

3

8. 

Windows that are part of the steam room should be double

paned and tempered safety glass.

9. 

Try to limit steam room ceiling height to 8 feet. Exceeding

8 feet may require a higher-rated steam generator.

10.

A warning sticker (shown below) has been provided in the

Information envelope. This sticker is to be secured to the
wall of the installed shower or steam enclosure.   

The CT series of steam generators are for

Commercial use only. 

BEFORE INSTALLING

IMPORTANT NOTES:

•  This document contains important safety, operation and

maintenance information. Leave this document with the
manager. Do not discard this document.

•  Discontinue use of the steam generator and control if

the steam generator or control are damaged or otherwise
not functioning properly. Doing so may result in an inop-
erative or hazardous installation

IMPORTANT: 

The following general information should be

used in conjunction with consultations with an architect,
designer and contractor in determining factors necessary
in providing a suitable and safe steam room.

Read these instructions before installation or service.
Although this CT steambath generator has been fully quali-
fied for shipment by Mr.Steam, the following must be
reviewed for proper, safe and enjoyable steam bathing:

•  Verify that the model and accessories are correct, includ-

ing incoming line voltage.

• Insure steambath generator has been correctly sized for

the steambath room. Pay particular attention to room
volume and construction. If any questions, please refer to
Mr.  Steam sizing and selection guide on page 2.

STEAM ROOM GUIDELINES

1. 

Steam room must be completely enclosed, with full

walls, door, floor and ceiling.

2.

It is recommended that a gasketed door is used for

heat sealing and steam containment.

3.

If tile-type or other smooth surfaced flooring is used

provide suitable anti-skid strips or equivalent, to 
prevent user slipping and injury.

4. 

Walls and ceilings must be constructed of water-

resistant, non-corrosive surface, such as tile, 
marble, molded acrylic, or other non-porous material. 
The ceiling should be sloped to prevent dripping of
condensate.  

If acrylic, fiberglass or other non-heat

resistant materials are used as part of the steam
room enclosure. Consult with the material manufac-
ture and see pg. 6, "Steamhead" for additional
details.

5.

Provide a floor drain.

6. 

No heating, venting or air conditioning devices

should be installed inside the steam room.

7.

Steam room tile construction information is 

available from the Tile Council of America, Inc. by
purchasing the TCA Handbook for Ceramic Tile
Installation. Tel: (864) 646-8453 or www.tileusa.com.

!

WA R N I N G

•  Marble or glass walls or ceilings, or exterior walls “ENLARGE”

the room’s size, requiring a generator larger than one based
only on the room’s cubic foot (L x H x W) volume.

•  The physical size of the unit, clearance for plumbing servic-

ing, and its distance from the steam room must all be consid-
ered before final installation.

• Consider any options and accessories before initiating installa-

tion. Read the Installation and Operation Manual of all
options and accessories available at www.mrsteam.com tech-
nical downloads.

IMPORTANT: 

CT units are intended to be operated with

Mr.Steam eTEMPO/PLUS, CT-STEAMSTOP controls only, and are
to be installed strictly in accordance with the specific instruc-
tions contained in this manual and as supplied in the manuals
provided with the controls.

ELECTRICAL SHOCK HAZARD. Mr.Steam

steam generators are connected to 240V line voltage and 
contain live electrical components.  All installation and service
to be performed by qualified and licensed electricians and
plumbers only. Installation or service by unqualified persons 
may void the warranty. 

!

WA R N I N G

REDUCE THE RISK OF OVERHEATING AND SCALDING

1. EXIT IMMEDIATELY IF UNCOMFORTABLE, DIZZY OR SLEEPY. 

STAYING TOO LONG IN A HEATED AREA IS CAPABLE OF CAUSING OVERHEATING.

2. CHILDREN UNDER THE AGE OF 16 SHOULD NOT USE THE STEAM BATH.
3. CHECK WITH A DOCTOR BEFORE USE IF PREGNANT, DIABETIC, IN POOR 

HEALTH OR UNDER MEDICAL CARE.

4. BREATHING HEATED AIR IN CONJUNCTION WITH CONSUMPTION OF ALCOHOL, 

DRUGS, OR MEDICATION IS CAPABLE OF CAUSING UNCONSCIOUSNESS.

5. DO NOT CONTACT STEAM HEAD OR STEAM AT THE STEAM HEAD.

REDUCE THE RISK OF SLIPPING AND FALL INJURY

1. USE CARE WHEN ENTERING OR EXITING THE STEAM ROOM. FLOOR MAY BE SLIPPERY.

NOTE: FOR ADDITIONAL SAFETY CONSIDERATIONS SEE OWNER’S MANUAL

mr

.

steam

®

43-20 34th Street , Long Island City  NY 11101    1 800 76 STEAM    www.mrsteam.com                            

PUR

100378   6.4/08 

WARNING

!

!

C A U T I O N

Summary of Contents for CT12E




























Reviews: