background image

23

USING MR.STEAM

®

ESSENTIAL OILS

Enjoy AromaSteam essential oils by placing a drop or two into an unheated AromaSteam steam-
head as shown in the illustration. Only use Mr.Steam AromaSteam essential oils in the Mr.Steam
AromaSteam steamhead.

Use essential oils with caution. Essential oils are for external use only. Keep

out of reach of children. Essential oils are highly concentrated and are potent substances and
should not be applied directly to the skin as they can be irritants. Use essential oils with caution. 

Place the drops into the Mr.steam AromaSteam steamhead recess prior to

turning on the steambath. Do not place drops in a hot steam head as SERIOUS INJURY CAN
RESULT IF YOU DO NOT FOLLOW THIS WARNING.

Start with one drop to gauge strength and suitability. Limit to a maximum of

a few drops for a steambathing session. 

The bather should exit the steambath IMMEDIATELY if dizziness occurs. If skin

irritation occurs stop using the oils immediately. Remove any excess oil by washing in mild soap
and water. If ingested, rinse mouth with water. Administer water or milk to dilute. Contact a
physician immediately.

Tightly close bottles when storing oils. 
Keep bottles away from sources of ignition.

!

C A U T I O N

!

C A U T I O N

!

C A U T I O N

!

C A U T I O N

!

C A U T I O N

Aromasteam steam head
(

install per instructions on pg.6

)

Steam emission slot

AromaSteam 
10ml bottle with 
integrated dropper

Recess for 

essential oil 

Aromatic oils should be added to

steamhead before turning on the steambath unit. 
DO NOT add oil during steambathing or when the 
steam head is heated.

mr

.

steam

®

club therapy

®

Installation, Operation & Maintenance Manual

______________________________________________________________________________

Summary of Contents for CT12E




























Reviews: