manualshive.com logo in svg

MQ Multiquip 24421, Operation And Parts Manual

The MQ Multiquip 24421 is a high-quality construction equipment designed for durability and efficiency. To ensure smooth operation and maintenance, it comes with an extensive Operation And Parts Manual. Download this essential manual for free from our website, enabling you to easily access all the necessary instructions and guidelines.

Share
Download
background image

PAGE 31 — JS36/30H55DE SERIES WALK-BEHIND TROWEL • OPERATION AND PARTS MANUAL — REV. #0 (5/02/16) 

4.  Using either a 5mm hex wrench, secure the 36" guard-

bumper ring assembly to the 30" guard ring base 

(Figure 40) using M8-1.25 x 25 BHC screws (12) and 

M8-1.25 nyloc nuts (12).

Figure 40. 36" Guard-Bumper Ring Installation

30” GUARD

RING BASE

M8-1.25 x 25

BHC SCREW

M8-1.25

NYLOC NUT

36” GUARD-BUMPER

RING AND HARDWARE

(PRE-ASSEMBLED) 

5.  Secure the 8" x 14" trowel blades (4) to the spider 

assembly (Figure 41) using a 5/32" hex wrench to 

install the 5/16-18 x 1-1/4" HHFS screws (4) and 

5/16-18 x 1-1/2" HHFS screws (4).

Figure 41. Trowel Blade Installation

 NOTICE

DO NOT

 install trowel blades (4) that extend beyond the 

outermost diameter of the guard ring bumper.

5/16-18 x 1-1/4”

HHFS SCREW

5/16-18 x 1-1/2”

HHFS SCREW

OPTIONS

Summary of Contents for 24421







































































Reviews:

No comments

Related manuals for 24421

ZIPPER MASCHINEN ZI-BG100Y User Manual preview
ZI-BG100Y
Brand: ZIPPER MASCHINEN Pages: 43

Brands by name

Popular brands

Load more brands