MQ Multiquip 24421 Operation And Parts Manual Download Page 16

Page: 16 / 70

PAGE 16 — JS36/30H55DE SERIES WALK-BEHIND TROWEL • OPERATION AND PARTS MANUAL —

REV. #0 (5/02/16)

Figure 3. Trowel Control and Components

14.

V-Belt Cover

— Remove this cover to gain access to

the V-belt.

NEVER

operate the trowel with this cover

removed.

15.

30" Guard Ring

—

NEVER

put hands or feet inside

guard ring while the machine is running.

16.

Blades

— This trowel is equipped with combination

blades. These blades are versatile and should take

care of most troweling needs. In addition float discs

can be attached to the trowel arms that will allow the

trowel to float on "wet" concrete.

TROWEL COMPONENTS

17.

30"/36" Bumper

— Allows the trowel to come closer

to troweling surface boundaries (i.e. walls) without

damaging the trowel blades.

18.

30"/36" Bumper Ring

— Allows the trowel to come

closer to troweling surface boundaries (i.e. walls)

without damaging the trowel blades.

19.

Gearbox

— Helical worm gear drive gearbox. Provides

rotation of blades via engine interface.

ALWAYS

check

gearbox oil level (sight glass) prior to each use. Fill with

recommended type gearbox oil.

Summary of Contents for 24421







































































Search results

Summary of Contents for 24421

Reviews:

Related manuals for 24421

Brands by name

Popular brands

MQ Multiquip 24421, Operation And Parts Manual

Search results

Summary of Contents for 24421

Reviews:

Related manuals for 24421

Brands by name

Popular brands