MQ Multiquip 24421 Operation And Parts Manual Download Page 19

Page: 19 / 70

PAGE 19 — JS36/30H55DE SERIES WALK-BEHIND TROWEL • OPERATION AND PARTS MANUAL — REV. #0 (5/02/16)

Safety Stop Switch Connection

1. Connect the black tail wire from the engine to the

top

black safety stop wire from the centrifugal stop switch

as shown in in Figure 9.

Figure 9. Safety Stop Switch Connection

2. Remove the existing bottom mounting screw on the

recoil starter cover (Figure 10) and connect the

bottom

wire from the centrifugal stop switch to this engine

ground point.

Figure 10. Engine Ground Point

NOTICE

If the throttle lever does not return to the "neutral"

position with throttle backed off, loosen adjuster nut 1/2

turn at a time, tighten and recheck. Readjust throttle

tension as necessary.

SAFETY STOP WIRE

CONNECTION POINT

BLACK

TAIL WIRE

TOP SAFETY

STOP WIRE

CENTRIFUGAL

STOP SWITCH

GROUND

WIRE

OFF

CENTRIFUGAL

STOP SWITCH

BOTTOM

EXISTING

SCREW

FUEL TANK

TOP

BLACK/RED

ENGINE

GROUND

POINT

RECOIL

STARTER

COVER

MALE

FEMALE

BLACK

TAIL WIRE

ASSEMBLY AND INSTALLATION

Pitch Cable Installation

1. Expose the pitch cable to maximum by turning the blade

pitch star wheel (Figure 11) fully counterclockwise for

no pitch (blades flat).

Figure 11. Blade Pitch Star Wheel

2. Remove brass set nuts #1 and #2 from the blade pitch

cable end as shown in (Figure 12).

Figure 12. Blade Pitch Cable

3. Insert the cable end through the yoke eyelet

(Figure 13). Tighten conical nut #1 by hand to remove

all the slack from the cable.

Figure 13. Pitch Cable Yoke Attachment

INCREASE

BLADE PITCH

(CW)

DECREASE

BLADE PITCH

(CCW)

BLADE

PITCH

CABLE

BRASS SET

NUT #1

BRASS SET

NUT #2

NOTICE

Nut #1 has a chamfer (taper) on the top. Put the nut on

with the chamfer (taper) against the yoke.

YOKE

EYELET

YOKE

BLADE

PITCH

CABLE

NUT #1

NUT #2

Summary of Contents for 24421







































































Search results

Summary of Contents for 24421

Reviews:

Related manuals for 24421

Brands by name

Popular brands

MQ Multiquip 24421, Operation And Parts Manual

Search results

Summary of Contents for 24421

Reviews:

Related manuals for 24421

Brands by name

Popular brands