background image

UNI MP100 User’s Guide 

 

 

Read Before Operating 

This manual must be carefully read by all individuals who have or will have the responsibility of 
using, maintaining  or servicing this  product.  The  product  will perform as  designed only  if it is 
used, maintained and serviced in accordance with the manufacturer’s instructions.   

  WARNING ! 

 

Never operate the monitor when the cover is removed.   

 

Remove the monitor cover and battery only in area known as non-hazardous. 

 

Use  only  mPower’s  lithium  battery  part  number 

M500-0001-000  [1.17.02.0002]

  (3.6V, 

2700mAH, AA size) or part No. ER14505 cell manufactured by EVE Energy Co., LTD 

 

This  instrument  has  not  been  tested  in  an  explosive  gas/air  atmosphere  having  an  oxygen 
concentration greater than 21%.   

 

Substitution of components will impair suitability for intrinsic safety.   

 

Substitution of components will void warranty. 

 

It  is  recommended  to  bump  test  with  a  known  concentration  gas  to  confirm  the  instrument  is 
functioning properly before use. 

 

Before  use,  ensure  that  the  colorless  ESD  layer  on  the  display  is  not  damaged  or  peeling.  (The 
blue protective film used for shipment may be removed.) 

  AVERTISSEMENT ! 

 

N'utilisez jamais le moniteur lorsque le couvercle est enlevé. 

 

Retirer  le  couvercle  du  moniteur  et  la  batterie  uniquement  dans  une  zone  connue  comme  non 
dangereuse. 

 

Utilisez uniquement la batterie au lithium de mPower, pièce No. 

M500-0001-000 [1.17.02.0002] 

(3.6V, 2700mAH, taille AA) ou celle de EVE Énergie Cie., Lt

é

, pièce No. ER14505. 

 

Cet instrument n'a pas été testé dans une atmosphère explosive gaz / air ayant une concentration 
en oxygène supérieure à 21%. 

 

La substitution de composants compromettra l'aptitude à la sécurité intrinsèque. 

 

La substitution des composants annulera la garantie. 

 

Il  est recommandé de tester avec un gaz de concentration connu pour confirmer que l'instrument f
onctionne correctement avant de l'utiliser. 

 

Avant l'utilisation, assurez-vous que la couche ESD incolore de l'écran n'est pas endommagée 
ou épluchée.

 

(Le film protecteur bleu peut être enlevé.) 

Proper Product Disposal at The End Of Life 

The  Waste  Electrical  and  Electronic  Equipment  (WEEE)  directive  (2002/96/EC)  is 
intended to promote recycling of electronic equipment and their components at end 
of life . This symbol (crossed-out wheeled bin) indicates separate collection of waste 
electrical  and  electronic  equipment  in  the  EU  countries.  This  product  may  contain 
one  or  more  Nickel-metal  hydride  (NiMH),  Lithium-ion,  or  Alkaline  batteries. 
Specific battery information is given in this user guide. Batteries must be recycled or 
disposed  of  properly.  At  the  end  of  its  life,  this  product  must  undergo  separate 
collection and recycling from general or household waste. Please use the return and 
collection system available in your country for the disposal of this product.

 

 

Summary of Contents for UNI MP100


























Reviews: