Mountain Models Flashback Manual Download Page 9 | Manualshive

Page: 9 / 62

Mountain Models Flashback Manual Download Page 9

Mountain Models Flashback

9

3.

Making sure the joints are snug and flush, apply thin CA to each of the joints. The glue

will be wicked into the balsa to form a secure bond, so it won’t take much glue to do
this. Make sure that you are only working on one joint at a time, and that the pieces

are firmly connected before moving to the next joint.

Be careful to keep your fingers as far away from the glue as possible; otherwise,
you might become a part of the model permanently. If you do get stuck, remove
yourself as carefully as possible, trying to avoid taking any of the wood with you.
Once separated, remove the CA glue from your fingers using nail polish remover, or
acetone, making sure you wash your hands thoroughly when done.

4.

Once the glue is dry, carefully remove them from the wax paper.

Attaching the Fuselage Reinforcement Pieces

The fuselage reinforcement pieces, or fuselage doublers, are used to reinforce the

fuselage and are placed on the interior walls of each fuselage side.

Yet again, I am just going to quickly mention that the fuselage sides must be mirror
images of each other. This includes making sure that the doublers are mirror images.

But don’t worry, we’re coming to the rescue, the pictures below show both sides just
so there’s no confusion…

For each fuselage side, you will need:

•

Fuselage Doubler (Figure B)

Notches and

grooves you use to

create the fuselage

sides

«
...
7
8
9
10
11
...
»

Summary of Contents for Flashback































































Reviews:

No comments