manualshive.com logo in svg

Motorola Symbol DS3407, Reference Manual

The Motorola Symbol DS3407 is a feature-rich barcode scanner designed for quick and accurate scanning. For comprehensive usage instructions, download the free Reference Manual from manualshive.com. This detailed manual is the perfect companion to help you make the most of your DS3407 scanner's capabilities.

Share
Download
background image

viii

Symbol DS3407 Product Reference Guide

Baud Rate  ............................................................................................................... 7-7
Parity ....................................................................................................................... 7-9
Stop Bit Select  ........................................................................................................ 7-10
Data Bits  ................................................................................................................. 7-10
Check Receive Errors  ............................................................................................. 7-11
Hardware Handshaking  .......................................................................................... 7-12
Software Handshaking ............................................................................................ 7-14
Host Serial Response Time-out  .............................................................................. 7-15
RTS Line State ........................................................................................................ 7-16
Beep on <BEL> ....................................................................................................... 7-16
Intercharacter Delay ................................................................................................ 7-17
Nixdorf Beep/LED Options ...................................................................................... 7-18
Ignore Unknown Characters  ................................................................................... 7-18

ASCII Character Set for RS-232  ................................................................................... 7-19

Chapter 8: USB Interface

Introduction ................................................................................................................... 8-1
Connecting a USB Interface  ......................................................................................... 8-2
USB Parameter Defaults  .............................................................................................. 8-3
USB Host Parameters  .................................................................................................. 8-4

USB Device Type .................................................................................................... 8-4
Symbol Native API (SNAPI) Status Handshaking ................................................... 8-5
USB Country Keyboard Types (Country Codes)  .................................................... 8-6
USB Keystroke Delay  ............................................................................................. 8-8
USB CAPS Lock Override  ...................................................................................... 8-8
USB Ignore Unknown Characters ........................................................................... 8-9
Emulate Keypad ...................................................................................................... 8-9
USB Keyboard FN 1 Substitution ............................................................................ 8-10
Function Key Mapping  ............................................................................................ 8-10
Simulated Caps Lock  .............................................................................................. 8-11
Convert Case  .......................................................................................................... 8-11

ASCII Character Set for USB ........................................................................................ 8-12

Chapter 9: 123 Scan

Introduction ................................................................................................................... 9-1
Communication with 123Scan  ...................................................................................... 9-1
123Scan Parameter  ...................................................................................................... 9-1

Chapter 10: Symbologies

Introduction ................................................................................................................... 10-1
Scanning Sequence Examples  ..................................................................................... 10-1
Errors While Scanning  .................................................................................................. 10-2
Symbology Parameter Defaults  .................................................................................... 10-2
UPC/EAN ...................................................................................................................... 10-7

Enable/Disable UPC-A ............................................................................................ 10-7
Enable/Disable UPC-E ............................................................................................ 10-7
Enable/Disable UPC-E1 .......................................................................................... 10-8

Summary of Contents for Symbol DS3407





















































































































































































































































































































































































































Reviews:

No comments

Related manuals for Symbol DS3407

ACS APG8201 PINhandy 1 Technical Specifications preview
APG8201 PINhandy 1
Brand: ACS Pages: 8
ID Mate Quest CD User Manual preview
Quest CD
Brand: ID Mate Pages: 36
Wasp WWS500 Programming Manual preview
WWS500
Brand: Wasp Pages: 42
Ting TING User Manual preview
TING
Brand: Ting Pages: 5
Prestigio PER3052 User Manual preview
PER3052
Brand: Prestigio Pages: 6
Datalogic QuickScan L QD2300 Quick Reference Manual preview
QuickScan L QD2300
Brand: Datalogic Pages: 32
Mode com MC-CR103 User Manual preview
MC-CR103
Brand: Mode com Pages: 12
Datalogic MAGELLAN 8300 Product Reference Manual preview
MAGELLAN 8300
Brand: Datalogic Pages: 558
Symbol PPT 8800 Product Reference Manual preview
PPT 8800
Brand: Symbol Pages: 328
Salto WRDx0A4 Series Installation Manual preview
WRDx0A4 Series
Brand: Salto Pages: 5
Datalogic POWERSCAN PBT7100 guide Product Reference Manual preview
POWERSCAN PBT7100 guide
Brand: Datalogic Pages: 352
Mircom TX3-CX-1NP Installation Manuals preview
TX3-CX-1NP
Brand: Mircom Pages: 4
HIKVISION 6954273653712 User Manual preview
6954273653712
Brand: HIKVISION Pages: 14
Blade T730 User Manual preview
T730
Brand: Blade Pages: 21
Jinmuyu MR730EC User Manual preview
MR730EC
Brand: Jinmuyu Pages: 7
AMT Datasouth Fastmark M4 Series Specifications preview
Fastmark M4 Series
Brand: AMT Datasouth Pages: 2
AMT Datasouth Fastmark M7 Series Service Manual preview
Fastmark M7 Series
Brand: AMT Datasouth Pages: 19
AMT Datasouth Fastmark M1/203dpi User Manual preview
Fastmark M1/203dpi
Brand: AMT Datasouth Pages: 32

Brands by name

Popular brands

Load more brands