manualshive.com logo in svg

Motorola Symbol DS3407, Reference Manual

Share
Download
Motorola Symbol DS3407 Reference Manual Download Page 114

7 - 14 Symbol DS3407 Product Reference Guide

Software Handshaking

This parameter offers control of the data transmission process in addition to, or instead of, that offered by hardware 
handshaking. There are five options.

If software handshaking and hardware handshaking are both enabled, hardware handshaking takes precedence.

•

None

: Select this option to transmit data immediately. The digital scanner expects no response from the host.

•

ACK/NAK

: If you select this option, after transmitting data, the digital scanner expects either an ACK or NAK 

response from the host. When it receives a NAK, the digital scanner transmits the same data again and waits 
for either an ACK or NAK. After three unsuccessful attempts to send data after receiving NAKs, the digital 
scanner issues an error indication and discards the data.

The digital scanner waits up to the programmable Host Serial Response Time-out to receive an ACK or NAK. 
If the digital scanner does not get a response in this time, it issues an error indication and discards the data. 
There are no retries when a time-out occurs.

•

ENQ

: If you select this option, the digital scanner waits for an ENQ character from the host before 

transmitting data. If the digital scanner does not receive an ENQ within the Host Serial Response Time-out, it 
issues an error indication and discards the data. The host must transmit an ENQ character at least every 
Host Serial Response Time-out to prevent transmission errors.

•

ACK/NAK with ENQ

: This combines the two previous options. For re-transmissions of data, due to a NAK 

from the host, an additional ENQ is not required.

•

XON/XOFF

: An XOFF character turns the digital scanner transmission off until the digital scanner receives 

an XON character. There are two situations for XON/XOFF:

•

The digital scanner receives an XOFF before it has data to send. When the digital scanner has data to 
send, it waits up to Host Serial Response Time-out for an XON character before transmission. If it does 
not receive an XON within this time, the digital scanner issues an error indication and discards the data.

•

The digital scanner receives an XOFF during a transmission. Data transmission then stops after sending 
the current byte. When the digital scanner receives an XON character, it sends the rest of the data 
message. The digital scanner waits indefinitely for the XON.

*

None

ACK/NAK

ENQ

Summary of Contents for Symbol DS3407





















































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands