manualshive.com logo in svg

Motorola Symbol DS3407, Reference Manual

Share
Download
Motorola Symbol DS3407 Reference Manual Download Page 133

USB Interface

8 - 9

USB Ignore Unknown Characters

This option applies only to the HID Keyboard Emulation device and IBM device. Unknown characters are 
characters the host does not recognize. Select 

Send Bar Codes With Unknown Characters

 to send all bar code 

data except for unknown characters. The digital scanner sounds no error beeps. 

If you select 

Do Not Send Bar Codes With Unknown Characters

, for IBM devices, bar codes containing at least 

one unknown character are not sent to the host, and the digital scanner sounds an error beep. For HID Keyboard 
Emulation devices, the bar code characters up to the unknown character are sent, and the scanner sounds an 
error beep.

Emulate Keypad

Enable this to send all characters as ASCII sequences over the numeric keypad. For example ASCII A transmits as 
“ALT make” 0 6 5 “ALT Break”.

*Send Bar Codes with Unknown Characters

(Transmit)

Do Not Send Bar Codes with Unknown Characters

(Disable)

*Disable Keypad Emulation

Enable Keypad Emulation

Summary of Contents for Symbol DS3407





















































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands